manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Troubleshooting 

Unusual Network Activity 

None of the devices assigned to one or more VLANs on an 802.1Q­
compliant switch are being recognized.  

If multiple VLANs are being used 

on ports connecting 802.1Q-compliant devices, inconsistent VLAN IDs may 
have been assigned to one or more VLANs. For a given VLAN, the same VLAN 
ID must be used on all connected 802.1Q-compliant devices. 

Link Configured for Multiple VLANs Does Not Support Traffic for One 
or More VLANs. 

One or more VLANs may not be properly configured as 

“Tagged” or “Untagged”. A VLAN assigned to a port connecting two 802.1Q­
compliant devices must be configured the same on both ports. For example, 
VLAN_1 and VLAN_2 use the same link between switch “X” and switch “Y”. 

Switch “Y” 

Switch “X” 

Link supporting VLAN_1 
and VLAN_2 

Port X-3 

Port Y- 7 

VLAN Port Assignment 

VLAN Port Assignment 

Port  VLAN_1

 VLAN_2 

Port  VLAN_1

 VLAN_2 

X-3   Untagged   Tagged  

Y-7   Untagged   Tagged 

Figure C-4.  Example of Correct VLAN Port Assignments on a Link 

1.   If VLAN_1 (VID=1) is configured as “Untagged” on port 3 on switch “X”, 

then it must also be configured as “Untagged” on port 7 on switch “Y”. 
Make sure that the VLAN ID (VID) is the same on both switches. 

2.   Similarly, if VLAN_2 (VID=2) is configured as “Tagged on the link port on 

switch “A”, then it must also be configured as “Tagged” on the link port 
on switch “B”. Make sure that the VLAN ID (VID) is the same on both 
switches. 

Duplicate MAC Addresses Across VLANs.  

The switch operates with mul­

tiple forwarding databases. Thus, duplicate MAC addresses occurring on 
different VLANs can appear where a device having one MAC address is a 
member of more than one 802.1Q VLAN, and the switch port to which the 
device is linked is using VLANs (instead of STP or trunking) to establish 
redundant links to another switch. If the other device sends traffic over 
multiple VLANs, its MAC address will consistently appear in multiple VLANs 
on the switch port to which it is linked. 

C-19 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

IBM N Series Setup And Configuration Manual preview
N Series
Brand: IBM Pages: 44
Sams DS-4 User Manual For Use And Maintenance preview
DS-4
Brand: Sams Pages: 10
Lantronix SM8TAT2SA Quick Start Manual preview
SM8TAT2SA
Brand: Lantronix Pages: 2
Gefen EXT-DVI-441DL User Manual preview
EXT-DVI-441DL
Brand: Gefen Pages: 31
ORiNG IGS-1082GP Quick Installation Manual preview
IGS-1082GP
Brand: ORiNG Pages: 2
Theben TIMEGUARD WF10COM Installation & Operating Instructions Manual preview
TIMEGUARD WF10COM
Brand: Theben Pages: 35
Control 4 C4-SW120277 Series Installation Manual preview
C4-SW120277 Series
Brand: Control 4 Pages: 4
Collective Minds Xbox One Media Hub Instruction Manual preview
Xbox One Media Hub
Brand: Collective Minds Pages: 19
Conrad 97 49 89 Operating Instructions Manual preview
97 49 89
Brand: Conrad Pages: 8
Lantech IGS-2206C User Manual preview
IGS-2206C
Brand: Lantech Pages: 118
A-Neuvideo ANI-3AUTOHDMI Instruction Manual preview
ANI-3AUTOHDMI
Brand: A-Neuvideo Pages: 16
Black Box SW045A-FFF Manual preview
SW045A-FFF
Brand: Black Box Pages: 9
Uniclass KLE Series User Manual preview
KLE Series
Brand: Uniclass Pages: 32
PowerShield PSMBSR10K Quick Manual preview
PSMBSR10K
Brand: PowerShield Pages: 2
ALFAtron SC61E Manual preview
SC61E
Brand: ALFAtron Pages: 23
Clare Controls CLIQ.mini Quick Start Manual preview
CLIQ.mini
Brand: Clare Controls Pages: 2
Kramer VP-443 User Manual preview
VP-443
Brand: Kramer Pages: 29
Niles ABS-1 Features & Specifications Manual preview
ABS-1
Brand: Niles Pages: 2

Brands by name

Popular brands

Load more brands