manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Switch Memory and Configuration 

Using Primary and Secondary Flash Image Options 

Operating Notes 

Default Boot Source.  

The switch reboots from primary flash by default 

unless you specify the secondary flash. 

Boot Attempts from an Empty Flash Location.  

In this case, the switch 

aborts the attempt and displays 

Image does not exist 

Operation aborted. 

Interaction of Primary and Secondary Flash Images with the Current 
Configuration.  

The switch has one startup-config file (page 6-3), which it 

always uses for reboots, regardless of whether the reboot is from primary or 
secondary flash. Also, for rebooting purposes, it is not necessary for the 
software image and the startup-config file to support identical software fea­
tures. For example, suppose you have just downloaded a software upgrade 
that includes new features that are not supported in the software you used to 
create the current startup-config file. In this case, the software simply assigns 
factory-default values to the parameters controlling the new features. Simi­
larly, If you create a startup-config file while using a version “Y” of the switch 
software, and then reboot the switch with an earlier software version “X” that 
does not include all of the features found in “Y”, the software simply ignores 
the parameters for any features that it does not support. 

6-22 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

N-Tron 100 Series User Manual & Installation Manual preview
100 Series
Brand: N-Tron Pages: 20
Barksdale 8000 Series Operating Instructions Manual preview
8000 Series
Brand: Barksdale Pages: 6
C&H Technologies M221 Specifications preview
M221
Brand: C&H Technologies Pages: 1
D-Box G3 Installation Manual preview
G3
Brand: D-Box Pages: 31
Fairchild FSD200 Manual preview
FSD200
Brand: Fairchild Pages: 14
S&C Omni-Rupter Installation Manual preview
Omni-Rupter
Brand: S&C Pages: 28
S&C Mark V Assembly And Installation Instructions Manual preview
Mark V
Brand: S&C Pages: 12
S&C Alduti-Rupter Instruction Sheet preview
Alduti-Rupter
Brand: S&C Pages: 24
S&C Alduti-Rupter Additional Instructions For Installation And Operation preview
Alduti-Rupter
Brand: S&C Pages: 24
S&C Vista SD Instruction Sheet preview
Vista SD
Brand: S&C Pages: 24
S&C Alduti-Rupter Installation Manual preview
Alduti-Rupter
Brand: S&C Pages: 28
S&C Vista SD Operation Manual preview
Vista SD
Brand: S&C Pages: 37
Oase Underwater Switch 24V DC/DMX/02 Operating Instructions Manual preview
Underwater Switch 24V DC/DMX/02
Brand: Oase Pages: 40
Conrad 97 49 89 Operating Instructions Manual preview
97 49 89
Brand: Conrad Pages: 8
LEGRAND Raritan Dominion LX II Quick Setup Manual preview
Raritan Dominion LX II
Brand: LEGRAND Pages: 7
H3C LS-5500-28C-PWR-SI-OVS Installation Manual preview
LS-5500-28C-PWR-SI-OVS
Brand: H3C Pages: 86
PKP PSA10 Instruction Manual preview
PSA10
Brand: PKP Pages: 11
XTBA Smart Switch 2:1 Manual preview
Smart Switch 2:1
Brand: XTBA Pages: 3

Brands by name

Popular brands

Load more brands