HP ProCurve 2610-24 Management And Configuration Manual Download Page 173 | Manualshive

Page: 173 / 464

background image

Time Protocols

SNTP: Viewing, Selecting, and Configuring

Table 9-1.SNTP Parameters

SNTP Parameter Operation

Time Sync
Method

Used to select either SNTP, TIMEP, or None as the time synchronization method.

SNTP Mode

Disabled

The Default. SNTP does not operate, even if specified by the Menu interface

Time Sync Method

parameter or the CLI

timesync

command.

Unicast

Directs the switch to poll a specific server for SNTP time synchronization. Requires at least one server
address.

Broadcast

Directs the switch to acquire its time synchronization from data broadcast by any SNTP server to the
network broadcast address. The switch uses the first server detected and ignores any others.
However, if the Poll Interval expires three times without the switch detecting a time update from the
original server, it the switch accepts a broadcast time update from the next server it detects.

Poll Interval
(seconds)

In Unicast Mode: Specifies how often the switch polls the designated SNTP server for a time update.
In Broadcast Mode: Specifies how often the switch polls the network broadcast address for a time
update.

Server Address

Used only when the

SNTP Mode

is set to

Unicast

. Specifies the IP address of the SNTP server that

the switch accesses for time synchronization updates. You can configure up to three servers; one
using the menu or CLI, and two more using the CLI. See “SNTP Unicast Time Polling with Multiple
SNTP Servers” on page 9-21.

Server Version

Default: 3; range: 1 - 7. Specifies the SNTP software version to use, and is assigned on a per-server
basis. The version setting is backwards-compatible. For example, using version 3 means that the
switch accepts versions 1 through 3.

Menu: Viewing and Configuring SNTP

To View, Enable, and Modify SNTP Time Protocol:

1. From the Main Menu, select:

2. Switch Configuration...

1. System Information

9-5

«
...
171
172
173
174
175
...
»

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Brand: Under Control Pages: 9

DES-3224 - Switch

Brand: D-Link Pages: 75

Brand: Xantech Pages: 4

QuantaMesh T1048-LB9M

Brand: QCT Pages: 34

Brand: SMART-AVI Pages: 2

Brand: ALFAtron Pages: 15

Brand: AETEK Pages: 2

Brand: SignaMax Pages: 6

Brand: Contec Pages: 38

Brand: Konig Pages: 40

Brand: Guntermann & Drunck Pages: 20

IES6300PRO Series

Brand: 3onedata Pages: 5

AVS-OP-1616-567SD

Brand: AMX Pages: 1

Brand: 3Com Pages: 104

Brand: Lantech Pages: 27

Brand: Advantech Pages: 73

Brand: Omron Pages: 13

920-9B210-00FN-0D0

Brand: Nvidia Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands