manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Troubleshooting 

Restoring a Flash Image 

Restoring a Flash Image 

The switch can lose its operating system if either the primary or secondary 
flash image location is empty or contains a corrupted OS file and an operator 
uses the 

erase flash

 command to erase a good OS image file from the opposite 

flash location. 

To Recover from an Empty or Corrupted Flash State.  

Use the switch’s 

console serial port to connect to a workstation or laptop computer that has 
the following: 

■

  

A terminal emulator program with Xmodem capability, such as the Hyper-
Terminal program included in Windows PC software. 

■

  

A copy of a good OS image file for the switch. 

N o t e    

The following procedure requires the use of Xmodem, and copies an OS image 
into primary flash only. 

This procedure assumes you are using HyperTerminal as your terminal emu­
lator. If you use a different terminal emulator, you may need to adapt this 
procedure to the operation of your particular emulator. 

1.   Start the terminal emulator program. 

2.   Ensure that the terminal program is configured as follows: 

■

  

Baud rate: 9600 

■

 

1 stop bit 

■

  

No parity 

■

 

No flow control 

■

  

8 Bits 

3.   Use the Reset button to reset the switch. The following prompt should 

then appear in the terminal emulator: 

Enter h or ? for help. 

=> 

C-45 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

D-Link DES-3224 - Switch User Manual preview
DES-3224 - Switch
Brand: D-Link Pages: 75
HPM XL770T Product Information preview
XL770T
Brand: HPM Pages: 4
DITEC COM500ER Installation Manual preview
COM500ER
Brand: DITEC Pages: 8
IOGear GUH420 Quick Start Manual preview
GUH420
Brand: IOGear Pages: 1
Network Technologies VEEMUX SM-nXm-15V-LC Installation And Operation Manual preview
VEEMUX SM-nXm-15V-LC
Brand: Network Technologies Pages: 46
Kobold PPS-1201 Operating Instructions Manual preview
PPS-1201
Brand: Kobold Pages: 10
GBC 34.0109.41 Quick Start Manual preview
34.0109.41
Brand: GBC Pages: 2
Accton Technology EH3008D Quick Installation Manual preview
EH3008D
Brand: Accton Technology Pages: 7
FCI FS10A Installation & Operation Manual preview
FS10A
Brand: FCI Pages: 78
Davey RainBank Installation Instructions preview
RainBank
Brand: Davey Pages: 2
KYLAND Ruby3A Hardware Installation Manual preview
Ruby3A
Brand: KYLAND Pages: 34
TRENDnet TEG-S80Dg Brochure & Specs preview
TEG-S80Dg
Brand: TRENDnet Pages: 2
Comprehensive CVG-21RCA User Manual preview
CVG-21RCA
Brand: Comprehensive Pages: 12
Rowley R-TEC Automation RTMWSR15C Manual preview
R-TEC Automation RTMWSR15C
Brand: Rowley Pages: 10
AMX Enova DGX 100 Series Quick Start Manual preview
Enova DGX 100 Series
Brand: AMX Pages: 2
Emulex InSpeed 350 User Manual preview
InSpeed 350
Brand: Emulex Pages: 75
Atlona AT-HD-SC-500 Manual preview
AT-HD-SC-500
Brand: Atlona Pages: 22
Heyer AGS 80 D Instructions For Use Manual preview
AGS 80 D
Brand: Heyer Pages: 29

Brands by name

Popular brands

Load more brands