manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Time Protocols  

SNTP: Viewing, Selecting, and Configuring 

Note that simply selecting a time synchronization protocol does not enable 
that protocol on the switch unless you also enable the protocol itself (step 2, 
above). For example, in the factory-default configuration, TimeP is the 
selected time synchronization method. However, because TimeP is disabled 
in the factory-default configuration, no time synchronization protocol is 
running. 

Disabling Time Synchronization 

You can use either of the following methods to disable time synchronization 
without changing the Timep or SNTP configuration: 

■

 

In the System Information screen of the Menu interface, set the 

Time 

Synch Method

 parameter to 

None

, then press

 [Enter]

, then 

[S]

 (for 

Save

). 

■

 

In the Global config level of the CLI, execute 

no timesync. 

SNTP: Viewing, Selecting, and 
Configuring 

SNTP Feature 

Default 

Menu 

CLI 

Web 

view the SNTP time synchronization configuration 

n/a 

page 9-5 

page 9-8

 — 

select SNTP as the time synchronization method 

timep 

page 9-6 

page 9-9 ff.

 — 

disable time synchronization 

timep 

page 9-6 

page 9-12

 — 

enable the SNTP mode (Broadcast, Unicast, or Disabled) 

disabled

 —

 broadcast 

n/a 

page 9-6 

page 9-9

 —

 unicast 

n/a 

page 9-6 

page 9-10

 —

 none/disabled 

n/a 

page 9-6 

page 9-13

 — 

configure an SNTP server address (for Unicast mode only)  none 

page 9-6 

page 9-10 ff.

 — 

change the SNTP server version (for Unicast mode only) 

3 

page 9-7 

page 9-12

 — 

change the SNTP poll interval 

720 seconds  page 9-7 

page 9-12

 — 

9-4 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Watchguard XTM 3 Series Hardware Manual preview
XTM 3 Series
Brand: Watchguard Pages: 26
Lantech IPES-5222T Series User Manual preview
IPES-5222T Series
Brand: Lantech Pages: 30
Origin Instruments Swifty SW2 User Manual preview
Swifty SW2
Brand: Origin Instruments Pages: 6
NeoPro DOC42 Integrator Manual preview
DOC42
Brand: NeoPro Pages: 36
MicroNet SP1659P User Manual preview
SP1659P
Brand: MicroNet Pages: 123
AMX AVS-OCT-4832-117 Product View preview
AVS-OCT-4832-117
Brand: AMX Pages: 1
Virtualfly SOLO Airliner RS User Manual preview
SOLO Airliner RS
Brand: Virtualfly Pages: 32
Allied Telesis Extricom AT-EXLS-3000 Installation And User Manual preview
Extricom AT-EXLS-3000
Brand: Allied Telesis Pages: 120
hager TX 206A Quick Start Manual preview
TX 206A
Brand: hager Pages: 4
Alloy POEFE8TV2 User Manual preview
POEFE8TV2
Brand: Alloy Pages: 13
Mach Power WL-CPE2G24D-075 User Manual preview
WL-CPE2G24D-075
Brand: Mach Power Pages: 44
Accton Technology 24/48 10/100 Ports + 2GE Management Manual preview
24/48 10/100 Ports + 2GE
Brand: Accton Technology Pages: 512
Omron G3M Specification Sheet preview
G3M
Brand: Omron Pages: 8
Magnetrol TD1 Series Installation And Operating Manual preview
TD1 Series
Brand: Magnetrol Pages: 32
NightStick 400B-RPS Instructions For Installing preview
400B-RPS
Brand: NightStick Pages: 2
StarTech.com MSTDP124DP Quick Install Manual preview
MSTDP124DP
Brand: StarTech.com Pages: 2
iPuray BRT-408 Product Description preview
BRT-408
Brand: iPuray Pages: 5
Eaton T03 I2-NA Series Instruction Leaflet preview
T03 I2-NA Series
Brand: Eaton Pages: 6

Brands by name

Popular brands

Load more brands