manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Port Status and Basic Configuration    

Using Friendly (Optional) Port Names 

For example: 

Friendly port names 
assigned in previous 
examples. 

Ports Without 
"Friendly" Name 

Figure 10-17.  Example of Friendly Port Name Data for All Ports on the Switch 

Port Without a "Friendly" 
Name 

Friendly port names 
assigned in previous 
examples. 

Figure 10-18.  Example of Friendly Port Name Data for Specific Ports on the Switch 

Including Friendly Port Names in Per-Port Statistics Listings. 

A 

friendly port name configured to a port is automatically included when you 
display the port’s statistics output. 

Syntax

: 

show interface <

port-number

> 

Includes the friendly port name with the port’s traffic 
statistics listing. 

For example, if you configure port A1 with the name “O’Connor_10.25.101.43”, 
the show interface output for this port appears similar to the following: 

10-36 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Talkswitch switch Start Manual preview
switch
Brand: Talkswitch Pages: 17
Cabletron Systems SmartCell 6A000 User Manual preview
SmartCell 6A000
Brand: Cabletron Systems Pages: 114
Cabletron Systems MRX Installation Manual preview
MRX
Brand: Cabletron Systems Pages: 62
Cabletron Systems CyberSWITCH CSX150 Quick Start Manual preview
CyberSWITCH CSX150
Brand: Cabletron Systems Pages: 49
Cabletron Systems Cabletron CyberSWITCH CSX5500 User Manual preview
Cabletron CyberSWITCH CSX5500
Brand: Cabletron Systems Pages: 729
3Com 3C17539 Datasheet preview
3C17539
Brand: 3Com Pages: 12
3Com S7906E - Switch Datasheet preview
S7906E - Switch
Brand: 3Com Pages: 8
Kramer VS-421 User Manual preview
VS-421
Brand: Kramer Pages: 8
D-Link DMS-1250 Series Hardware Installation Manual preview
DMS-1250 Series
Brand: D-Link Pages: 38
Eaton 9476-ET Instruction Manual preview
9476-ET
Brand: Eaton Pages: 43
ATEN CS1922M User Manual preview
CS1922M
Brand: ATEN Pages: 17
Barox PC-IA100 Series User Manual preview
PC-IA100 Series
Brand: Barox Pages: 7
ALFAtron ALF-MUH88TP-N Manual preview
ALF-MUH88TP-N
Brand: ALFAtron Pages: 68
Eaton Edison Cooper Power Series Installation And Operation Instructions Manual preview
Edison Cooper Power Series
Brand: Eaton Pages: 12
Kramer Sierra Pro XL 1608V5S Specifications preview
Sierra Pro XL 1608V5S
Brand: Kramer Pages: 2
Hisselektronik Safeline 2000 Light Manual For Programmering preview
Safeline 2000 Light
Brand: Hisselektronik Pages: 9
IPGARD SA-DVN-8D Quick Start Manual preview
SA-DVN-8D
Brand: IPGARD Pages: 2
Trust START-LINE AGC-3500 Important Information Manual preview
START-LINE AGC-3500
Brand: Trust Pages: 16

Brands by name

Popular brands

Load more brands