manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

MAC Address Management 

Overview 

Overview 

The switch assigns MAC addresses in these areas: 

■

  

For management functions: 

•   One Base MAC address assigned to the default VLAN (VID = 1) 

•   Additional MAC address(es) corresponding to additional  VLANs you 

configure in the switch 

■

  

For internal switch operations: One MAC address per port (See “CLI: 
Viewing the Port and VLAN MAC Addresses” on page D-4.) 

MAC addresses are assigned at the factory. The switch automatically 
implements these addresses for VLANs and ports as they are added to the 
switch. 

N o t e    

The switch’s base MAC address is also printed on a label affixed to the back 
of the switch. 

Determining MAC Addresses in the 
Switch 

MAC Address Viewing Methods 

Feature 

Default 

Menu 

CLI 

Web 

view switch’s base (default vlan) MAC  address 
and the addressing for any added VLANs 

n/a 

D-3 

D-4 

— 

view port MAC addresses (hexadecimal format) 

n/a 

— 

D-4 

— 

■

  

Use the menu interface

 to view the switch’s base MAC address and the 

MAC address assigned to any non-default VLAN you have configured on 
the switch. 

N o t e    

The switch’s base MAC address is used for the default VLAN (VID = 1) that is 
always available on the switch. 

D-2 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

D-Link xStack DGS-3420 Series How To Set Up preview
xStack DGS-3420 Series
Brand: D-Link Pages: 2
D-Link DXS-3600-32S Quick Installation Manual preview
DXS-3600-32S
Brand: D-Link Pages: 29
D-Link DWS-1008 User Manual preview
DWS-1008
Brand: D-Link Pages: 454
D-Link DWS-1008 Product Manual preview
DWS-1008
Brand: D-Link Pages: 502
D-Link DGS-3312SR Product Manual preview
DGS-3312SR
Brand: D-Link Pages: 244
D-Link GO-SW-5G User Manual preview
GO-SW-5G
Brand: D-Link Pages: 20
D-Link DES-1008E Quick Install Manual preview
DES-1008E
Brand: D-Link Pages: 2
D-Link KVM-440 User Manual preview
KVM-440
Brand: D-Link Pages: 37
D-Link DES-1018DG Quick Installation Manual preview
DES-1018DG
Brand: D-Link Pages: 28
Kathrein EXR 221 Quick Start Manual preview
EXR 221
Brand: Kathrein Pages: 8
Nayar Systems Switch Manual preview
Switch
Brand: Nayar Systems Pages: 21
Kathrein EXD 1532 User Manual preview
EXD 1532
Brand: Kathrein Pages: 24
Kasia Switch Installation Manual preview
Switch
Brand: Kasia Pages: 5
ATZ HDMI-161SM Manual preview
HDMI-161SM
Brand: ATZ Pages: 8
Gefen EXT-DVIKVM-441DL User Manual preview
EXT-DVIKVM-441DL
Brand: Gefen Pages: 32
hager TS 204 User Instruction preview
TS 204
Brand: hager Pages: 2
UNICOM Smart-Switch/801 FEP-30109T-C User Manual preview
Smart-Switch/801 FEP-30109T-C
Brand: UNICOM Pages: 22
Pakedge Device & Software S8Mpdp Quick Start Manual preview
S8Mpdp
Brand: Pakedge Device & Software Pages: 14

Brands by name

Popular brands

Load more brands