manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Monitoring and Analyzing Switch Operation 

Status and Counters Data 

Prompt for Selecting 
the Port To Search 

Figure B-10. Listing MAC Addresses for a Specific Port 

2.   Use the Space bar to select the port you want to list or search for MAC 

addresses, then press 

[Enter]

 to list the MAC addresses detected on that 

port. 

Determining Whether a Specific Device Is Connected to the Selected 
Port. 

Proceeding from step 2, above: 

1.   Press 

[S]

 (for 

Search

), to display the following prompt: 

Enter MAC address: _ 

2.   Type the MAC address you want to locate and press 

[Enter]

. The address 

is highlighted if found. If the switch does not find the address, it leaves 
the MAC address listing empty. 

3.   Press 

[P]

 (for 

Prev page

) to return to the previous per-port listing. 

CLI Access for MAC Address Views and Searches 

Syntax

: 

show mac-address 

[vlan 

< vlan-id >

] 

[ethernet]

< port-list >

] 

[< mac-addr >] 

To List All Learned MAC Addresses on the Switch, with The Port 
Number on Which Each MAC Address Was Learned. 

ProCurve> show mac-address 

To List All Learned MAC Addresses on one or more ports, with Their 

B-15 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

3One data IPS7110-2GC-8POE Quick Installation Manual preview
IPS7110-2GC-8POE
Brand: 3One data Pages: 3
Silent Gliss 0913 Installation, Programming And Operation Instructions preview
0913
Brand: Silent Gliss Pages: 4
Accton Technology EtherHub-16 Quick Start Manual preview
EtherHub-16
Brand: Accton Technology Pages: 10
Lancom GS-3528X Installation Manual preview
GS-3528X
Brand: Lancom Pages: 23
steute Ex 355 Mounting And Wiring Instructions preview
Ex 355
Brand: steute Pages: 20
Ametek SIL IntelliPoint RF S*R*L Series Installation And Operating Instructions Manual preview
SIL IntelliPoint RF S*R*L Series
Brand: Ametek Pages: 93
Festo CRSMEO-4 Series Operating Instructions Manual preview
CRSMEO-4 Series
Brand: Festo Pages: 16
H3C S5130S-EI series Hardware Information preview
S5130S-EI series
Brand: H3C Pages: 67
Dahua PFS4226-24ET-240 User Manual preview
PFS4226-24ET-240
Brand: Dahua Pages: 3
3Com 3CB9E7 - CoreBuilder 9000 Chassis Switch Getting Started Manual preview
3CB9E7 - CoreBuilder 9000 Chassis Switch
Brand: 3Com Pages: 132
Cypress CLUX-C61C Operation Manual preview
CLUX-C61C
Brand: Cypress Pages: 16
TRENDnet TEG-S41SX Specifications preview
TEG-S41SX
Brand: TRENDnet Pages: 2
Cabletron Systems SEH-22 User Manual preview
SEH-22
Brand: Cabletron Systems Pages: 56
Cabletron Systems 42T User Manual preview
42T
Brand: Cabletron Systems Pages: 105
CYP CMSI-4H4CV Operation Manual preview
CMSI-4H4CV
Brand: CYP Pages: 20
Eneo 230033 Quick Installation Manual preview
230033
Brand: Eneo Pages: 19
DigitalZone Sound Switcher Installation Manual preview
Sound Switcher
Brand: DigitalZone Pages: 20
Planet XGS-6350-12X8TR Quick Installation Manual preview
XGS-6350-12X8TR
Brand: Planet Pages: 16

Brands by name

Popular brands

Load more brands