manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Selecting a Management Interface 

Advantages of Using the Menu Interface 

Advantages of Using the Menu Interface 

Figure 2-1.  Example of the Console Interface Display 

■

  

Provides quick, easy management access

 to a menu-driven subset of 

switch configuration and performance features: 

•  IP addressing 

•  Spanning Tree 

•  VLANs and GVRP 

•  System information 

•  Port Security 

•  Passwords 

•  Port and Static Trunk  

•  SNMP communities 

Group 

•  Time protocols 

•  Stack Management 

The menu interface also provides access for: 

•  Setup screen 

•  Switch and port statistic and 

•  Event Log display 

counter displays 

•  Switch and port  

• Reboots   

status displays 

•  Software downloads 

■

  

Offers out-of-band access 

(through the RS-232 connection) to the 

switch, so network bottlenecks, crashes, lack of configured or correct IP 
address, and network downtime do not slow or prevent access 

■

  

Enables Telnet (in-band) access 

to the menu functionality. 

2-3 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Yamamoto Electric Works Co., Ltd. MS65F Instruction Manual preview
MS65F
Brand: Yamamoto Electric Works Co., Ltd. Pages: 15
ANTAIRA LMP-1204G-SFP Series Hardware Manual preview
LMP-1204G-SFP Series
Brand: ANTAIRA Pages: 20
Key Digital KD-PS42 Manual preview
KD-PS42
Brand: Key Digital Pages: 31
ALFAtron ALF-WP70T/RS User Manual preview
ALF-WP70T/RS
Brand: ALFAtron Pages: 15
AETEK C11-082-32-120 Quick Installation Manual preview
C11-082-32-120
Brand: AETEK Pages: 2
SignaMax 065-7331GPOEP User Manual preview
065-7331GPOEP
Brand: SignaMax Pages: 6
Compaq StorageWorks SAN Switch Integrated/32 Installation And Hardware Manual preview
StorageWorks SAN Switch Integrated/32
Brand: Compaq Pages: 104
One Control Crocodile Tail Loop Setup preview
Crocodile Tail Loop
Brand: One Control Pages: 9
I-Tech NVCIP800 User Manual preview
NVCIP800
Brand: I-Tech Pages: 29
Thinklogical OriginKVM 41 Product Manual preview
OriginKVM 41
Brand: Thinklogical Pages: 17
EtherWAN EX24000 User Manual preview
EX24000
Brand: EtherWAN Pages: 239
SLV 470819 Quick Installation Manual preview
470819
Brand: SLV Pages: 22
Radio Shack 15-316 User Manual preview
15-316
Brand: Radio Shack Pages: 8
QSFPTEK S5300-48T4X Quick Start Manual preview
S5300-48T4X
Brand: QSFPTEK Pages: 8
Raisecom ISCOM2600G (A) Series Product Description preview
ISCOM2600G (A) Series
Brand: Raisecom Pages: 96
3onedata IES2016-16T Series Quick Installation Manual preview
IES2016-16T Series
Brand: 3onedata Pages: 3
TeleAdapt ConferenceHub TA-6500 User Manual preview
ConferenceHub TA-6500
Brand: TeleAdapt Pages: 16
Blue Sea Systems 8689 Manual preview
8689
Brand: Blue Sea Systems Pages: 2

Brands by name

Popular brands

Load more brands