manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

-----           ----------  -------- -------  -------

Switch Memory and Configuration 

Using Primary and Secondary Flash Image Options 

For example, if the switch is using a software version of R.01.01 stored in 
Primary flash, 

show version 

produces the following: 

ProCurve(config)# show version 

Image stamp:  

/sw/code/build/info (s03)

      Nov 01 2007 10:50:26
      R.01.01
      501 

Boot Image:      Primary 

Figure 6-7.  Example Showing the Identity of the Current Flash Image 

Determining Whether the Flash Images Are Different Versions. 

If the 

flash image sizes in primary and secondary are the same, then in almost every 
case, the primary and secondary images are identical. This command provides 
a comparison of flash image sizes, plus the boot ROM version and from which 
flash image the switch booted. For example, in the following case, the images 
are different versions of the switch software and the switch is running on the 
version stored in the secondary flash image: 

ProCurve(config)# show flash

 

Image           Size(Bytes)

 Date 

Version  Build #

 

The unequal code 

Primary Image   : 3961354   08/01/07 R.11.02 #   104 

size and differing 

Secondary Image : 3916654   07/06/07 R.11.01 #  1242 

dates indicate two 

Boot Rom Version: R.10.03 

different versions of 

Current Boot  

: Primary 

the software. 

Figure 6-8.  Example Showing Different Flash Image Versions 

Determining Which Flash Image Versions Are Installed.  

The 

show ver­

sion

 command displays which software version the switch is currently running 

and whether that version booted from primary or secondary flash. Thus, if the 
switch booted from primary flash, you will see the version number of the 
software image stored in primary flash, and if the switch booted from second­
ary flash, you will see the version number of the software version stored in 
secondary flash. Thus, by using 

show version

, then rebooting the switch from 

the opposite flash image and using 

show version

 again, you can determine the 

version(s) of switch software in both flash sources. For example: 

6-14 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

GE SE-100E Instructions Manual preview
SE-100E
Brand: GE Pages: 20
Hama S2100 Operating Instruction preview
S2100
Brand: Hama Pages: 18
Talkswitch switch Start Manual preview
switch
Brand: Talkswitch Pages: 17
D-Link DWS-3160-24TC Datasheet preview
DWS-3160-24TC
Brand: D-Link Pages: 7
Lindy 32351 Manual preview
32351
Brand: Lindy Pages: 70
DITEC COM500ER Installation Manual preview
COM500ER
Brand: DITEC Pages: 8
Erbe 20186-007 Manual preview
20186-007
Brand: Erbe Pages: 118
Crestron CLW-LSWEX-1GD Installation And Operation Manual preview
CLW-LSWEX-1GD
Brand: Crestron Pages: 2
TAXON TOOLS Scart Switch Manual preview
Scart Switch
Brand: TAXON TOOLS Pages: 9
Guralp Systems NAM MkII Quick Start Manual preview
NAM MkII
Brand: Guralp Systems Pages: 22
NETGEAR GS108P-100NAS Installation Manual preview
GS108P-100NAS
Brand: NETGEAR Pages: 2
Ubiquiti 0817882025218 Quick Start Manual preview
0817882025218
Brand: Ubiquiti Pages: 23
Exsys EX-1178 Manual preview
EX-1178
Brand: Exsys Pages: 2
QSFPTEK S5300-48T4X Quick Start Manual preview
S5300-48T4X
Brand: QSFPTEK Pages: 8
Hama 42556 Operating Instructions Manual preview
42556
Brand: Hama Pages: 36
Enterasys SecureStack B2 B2G124-48P Hardware Installation Manual preview
SecureStack B2 B2G124-48P
Brand: Enterasys Pages: 91
Synergy Global Technology LCDK1023 User Manual preview
LCDK1023
Brand: Synergy Global Technology Pages: 9
Pakedge Device & Software SE-8P User Manual preview
SE-8P
Brand: Pakedge Device & Software Pages: 8

Brands by name

Popular brands

Load more brands