manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

File Transfers 

Downloading Switch Software 

Switch-to-Switch Download 

You can use TFTP to transfer a switch software file between two ProCurve 
switches that use the same software code base. The menu interface enables 
you to transfer primary-to-primary or secondary-to-primary. The CLI enables 
all combinations of flash location options. 

Menu: Switch-to-Switch Download to Primary Flash 

Using the menu interface, you can download switch software from either the 
primary or secondary flash of one switch to the primary flash of another 
switch. 

1.   From the switch console Main Menu in the switch to receive the down­

load, select 

7. Download OS

 screen. 

2.   Ensure that the 

Method 

parameter is set to 

TFTP

 (the default). 

3.   In the 

TFTP Server

 field, enter the IP address of the remote switch contain­

ing the switch software you want to download. 

4.   For the 

Remote File Name

, enter one of the following: 

•  

To download the switch software from the primary flash of the source 
switch, type 

flash

 or 

/os/primary 

in lowercase characters. 

•   To download the switch software from the secondary flash of the 

source switch, type 

/os/secondary

. 

5.   Press 

[Enter]

, then 

[X]

 (for 

eXecute

) to begin the switch software download. 

6.   A “progress” bar indicates the progress of the download. When the entire 

operating system has been received, all activity on the switch halts and 
the following messages appear: 

Validating and writing system software to FLASH... 

7.   After the primary flash memory has been updated with the new operating 

system, you must reboot the switch to implement the newly downloaded 
software. From the Main Menu, press 

[6]

 (for 

Reboot Switch

). You will then 

see this prompt: 

Continue reboot of system?  :  No 

Press the space bar once to change 

No

 to 

Yes

, then press 

[Enter]

 to begin 

the reboot. 

8.   To confirm that the operating system downloaded correctly: 

a.   From the Main Menu, select 

Status and Counters 

A-14 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Movie Vision VCS-3 Installation And User Manual preview
VCS-3
Brand: Movie Vision Pages: 2
SMC Networks SMC8724-10BT Technical Specifications preview
SMC8724-10BT
Brand: SMC Networks Pages: 2
Omega Engineering PSW32 SERIES User Manual preview
PSW32 SERIES
Brand: Omega Engineering Pages: 8
ATZ HDMI-161SM Manual preview
HDMI-161SM
Brand: ATZ Pages: 8
Gefen EXT-DVIKVM-441DL User Manual preview
EXT-DVIKVM-441DL
Brand: Gefen Pages: 32
Amped Wireless APA2600M Installation And Configuration Manual preview
APA2600M
Brand: Amped Wireless Pages: 22
YA Fusion Z-7799 Instruction Manual preview
Fusion Z-7799
Brand: YA Pages: 47
Enterasys Matrix DFE-Gold 4G4202-60 Hardware Installation Manual preview
Matrix DFE-Gold 4G4202-60
Brand: Enterasys Pages: 78
ZENEC 2E-AVS Instruction Manual preview
2E-AVS
Brand: ZENEC Pages: 16
Kobold PPS-1201 Operating Instructions Manual preview
PPS-1201
Brand: Kobold Pages: 10
netvox ZigBee Z815B User Manual preview
ZigBee Z815B
Brand: netvox Pages: 14
EtherWAN EX62000 Installation Manual preview
EX62000
Brand: EtherWAN Pages: 2
Inscape Data Link Power LPS2400-T1 User Manual preview
Link Power LPS2400-T1
Brand: Inscape Data Pages: 8
Gembird UHB-U3P7P-01 User Manual preview
UHB-U3P7P-01
Brand: Gembird Pages: 2
Oehlbach UltraHD Switch 3:1 User Manual preview
UltraHD Switch 3:1
Brand: Oehlbach Pages: 20
Cabletron Systems 9F426-03 Appendix preview
9F426-03
Brand: Cabletron Systems Pages: 14
SMC Networks ZSE1 Series User Manual preview
ZSE1 Series
Brand: SMC Networks Pages: 6
Patton FiberPlex 1004E User Manual preview
FiberPlex 1004E
Brand: Patton Pages: 39

Brands by name

Popular brands

Load more brands