HP ProCurve 2610-24 Management And Configuration Manual Download Page 154

Page: 154 / 464

Configuring IP Addressing

IP Configuration

For descriptions of these
parameters, see the
online Help for this
screen.

Before using the DHCP/
Bootp option, refer to
“DHCP/Bootp
Operation” on page 8-12.

Figure 8-1. Example of the IP Service Configuration Screen without Multiple

VLANs Configured

2. Press

[E]

(for

Edit

3. If the switch needs to access a router, for example, to reach off-subnet

destinations, select the

Default Gateway

field and enter the IP address of

the gateway router.

4. If you need to change the packet Time-To-Live (TTL) setting, select

Default

TTL

and type in a value between 2 and 255 (seconds).

5. To configure IP addressing, select

IP Config

and do one of the following:

• If you want to have the switch retrieve its IP configuration from a

DHCP or Bootp server, at the

IP Config

field, keep the value as

DHCP/

Bootp

and go to step 8.

• If you want to manually configure the IP information, use the Space

bar to select

Manual

and use the

[Tab]

key to move to the other IP

configuration fields.

6. Select the

IP Address

field and enter the IP address for the switch.

7. Select the

Subnet Mask

field and enter the subnet mask for the IP address.

8. Press

[Enter]

, then

[S]

(for

Save

8-6

Summary of Contents for ProCurve 2610-24
















































































































































































































































































































































































































































































Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands

HP ProCurve 2610-24, Management And Configuration Manual

Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands