HP ProCurve 2610-24 Management And Configuration Manual Download Page 398 | Manualshive

Page: 398 / 464

background image

Troubleshooting

Unusual Network Activity

This can also happen, for example, if the server is first configured to issue IP
addresses with an unlimited duration, then is subsequently configured to issue
IP addresses that will expire after a limited duration. One solution is to
configure “reservations” in the DHCP server for specific IP addresses to be
assigned to devices having specific MAC addresses. For more information,
refer to the documentation for the DHCP server.

One indication of a duplicate IP address in a DHCP network is this Event Log
message:

ip: Invalid ARP source:

IP address

on

IP address

where:

both instances of

IP address

are the same address, indicating the

IP address that has been duplicated somewhere on the network.

The Switch Has Been Configured for DHCP/Bootp Operation, But Has
Not Received a DHCP or Bootp Reply.

When the switch is first config

ured for DHCP/Bootp operation, or if it is rebooted with this configuration, it
immediately begins sending request packets on the network. If the switch does
not receive a reply to its DHCP/Bootp requests, it continues to periodically
send request packets, but with decreasing frequency. Thus, if a DHCP or Bootp
server is not available or accessible to the switch when DHCP/Bootp is first
configured, the switch may not immediately receive the desired configuration.
After verifying that the server has become accessible to the switch, reboot the
switch to re-start the process.

Prioritization Problems

Ports configured for non-default prioritization (level 1 - 7) are not
performing the specified action.

If the ports were placed in a trunk group

after being configured for non-default prioritization, the priority setting was
automatically reset to zero (the default). Ports in a trunk group operate only
at the default priority setting.

IGMP-Related Problems

IP Multicast (IGMP) Traffic That Is Directed By IGMP Does Not Reach
IGMP Hosts or a Multicast Router Connected to a Port.

IGMP must

be enabled on the switch and the affected port must be configured for “Auto”
or “Forward” operation.

IP Multicast Traffic Floods Out All Ports; IGMP Does Not Appear To

C-8

«
...
396
397
398
399
400
...
»

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Brand: Vector Pages: 6

Brand: DITEC Pages: 8

Brand: Campbell Pages: 10

Brand: Cabletron Systems Pages: 120

Brand: hager Pages: 4

UHB-U3P1U2P3P-01

Brand: Gembird Pages: 2

TigerAccess SMC7824M/FSW

Brand: SMC Networks Pages: 2

Brand: ADC Pages: 75

Brand: hager Pages: 2

Brand: HIKVISION Pages: 25

Brand: GeoVision Pages: 7

Brand: Harman Pages: 50

Brand: Tabs Pages: 4

Brand: Cypress Pages: 16

Brand: TRENDnet Pages: 2

Brand: Linkskey Pages: 2

Brand: pro bel Pages: 12

EdgeSwitch 8 150W

Brand: Ubiquiti Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands