HP ProCurve 2610-24 Management And Configuration Manual Download Page 36 | Manualshive

Page: 36 / 464

background image

Selecting a Management Interface

Advantages of Using ProCurve Manager or ProCurve Manager Plus

Advantages of Using ProCurve Manager
or ProCurve Manager Plus

You can operate ProCurve Manager and ProCurve Manager Plus (PCM and
PCM+) from a PC on the network to monitor traffic, manage your hubs and
switches, and proactively recommend network changes to increase network
uptime and optimize performance. Easy to install and use, PCM and PCM+ are
the answers to your management challenges.

PCM and PCM+ enable greater control, uptime, and performance in your
network:

■

Features and benefits of ProCurve Manager:

•

Network Status Summary:

Upon boot-up, a network status screen

displays high-level information on network devices, end nodes,
events, and traffic levels. From here, users can research any one of
these areas to get more details.

•

Alerts and Troubleshooting:

An events summary screen displays

alerts to the user and categorizes them by severity, making it easier
to track where bottlenecks and issues exist in the network. Alerts
present detailed information on the problem, even down to the spe
cific port.

•

Automatic Device Discovery:

This feature is customized for fast

discovery of all ProCurve manageable network devices. The user can
define which IP subnets to discover.

•

Topology and Mapping:

This feature automatically creates a map

of discovered network devices. Maps are color-coded to reflect device
status and can be viewed at multiple levels (physical view, subnet
view, or VLAN view).

•

Device Management:

Many device-focused tasks can be performed

directly by the software, or the user can access web-browser and
command-line interfaces with the click of a button to manage individ
ual devices from inside the tool.

■

Features and benefits of ProCurve Manager Plus:

•

All of the Features of ProCurve Manager:

Refer to the above

listing.

•

In-Depth Traffic Analysis:

An integrated, low-overhead traffic

monitor interface shows detailed information on traffic throughout
the network. Using enhanced traffic analysis protocols such as

2-6

«
...
34
35
36
37
38
...
»

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

WJSX150 - SWITCHER - ADDENDUM

Brand: Panasonic Pages: 48

Brand: Dataprobe Pages: 3

Brand: Panasonic Pages: 206

S5560S-EI Series

Brand: H3C Pages: 37

OfficeConnect WX4400

Brand: 3Com Pages: 528

Brand: Delta Electronics Pages: 1

Brand: Gefen Pages: 31

Brand: ORiNG Pages: 2

TIMEGUARD WF10COM

Brand: Theben Pages: 35

MMAC-Plus 9T125-24

Brand: Cabletron Systems Pages: 36

Brand: hager Pages: 2

Brand: HIKVISION Pages: 25

Brand: Black Box Pages: 20

Brand: Rackmount Pages: 16

Brand: Epcom Pages: 2

Brand: Pakedge Device & Software Pages: 8

Brand: CTC Union Pages: 14

PSEN ma2.1p/ATEX

Brand: Pilz Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands