HP ProCurve 2610-24 Management And Configuration Manual Download Page 187 | Manualshive

Page: 187 / 464

background image

Time Protocols

TimeP: Viewing, Selecting, and Configuring

The commands and output would appear as follows:

1

2

3

4

show timep

displays the TimeP configuration and also shows

that SNTP is the currently active time synchronization mode.

show timep

again displays the TimeP configuration and shows that TimeP is

now the currently active time synchronization mode.

Figure 9-12. Example of Enabling TimeP Operation in DHCP Mode

Enabling Timep in Manual Mode.

Like DHCP mode, configuring TimeP for

Manual

mode enables TimeP. However, for manual operation, you must also

specify the IP address of the TimeP server. (The switch allows only one TimeP
server.) To enable the TimeP protocol:

Syntax

:

timesync timep

Selects Timep.

ip timep manual <ip-addr>

Activates TimeP in Manual mode with a specified TimeP
server.

no ip timep

Disables TimeP

.

N o t e

To change from one TimeP server to another, you must (1) use the

no ip timep

command to disable TimeP mode, and then reconfigure TimeP in Manual
mode with the new server IP address.

For example, to select TimeP and configure it for manual operation using a
TimeP server address of 10.28.227.141 and the default poll interval (720
minutes, assuming the TimeP poll interval is already set to the default):

ProCurve(config)# timesync timep

Selects TimeP.

ProCurve(config)# ip timep manual 10.28.227.141

Activates TimeP in Manual mode.

9-19

«
...
185
186
187
188
189
...
»

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Brand: 3Com Pages: 8

Brand: Campbell Pages: 14

Brand: JB Systems Light Pages: 15

Brand: l-com Pages: 12

Brand: Manhattan Pages: 2

Brand: ASTEK Pages: 3

2X2 VGA SWITCHER

Brand: Gefen Pages: 12

Brand: Ask Pages: 4

FlowPoint 2100 12

Brand: Cabletron Systems Pages: 36

Brand: Hawking Pages: 2

Brand: IPGARD Pages: 2

START-LINE AGC-3500

Brand: Trust Pages: 16

Brand: Zektor Pages: 41

Brand: Kramer Pages: 2

Brand: Penguin Computing Pages: 71

TNS5000D Series

Brand: 3onedata Pages: 3

Brand: LINK-MI Pages: 9

Brand: MicroNet Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands