HP ProCurve 2610-24 Management And Configuration Manual Download Page 367 | Manualshive

Page: 367 / 464

background image

Monitoring and Analyzing Switch Operation

Status and Counters Data

Menu Access To Status and Counters

Beginning at the Main Menu, display the Status and Counters menu by select
ing:

1. Status and Counters

Figure B-1. The Status and Counters Menu

Each of the above menu items accesses the read-only screens described on
the following pages. Refer to the online help for a description of the entries
displayed in these screens.

B-5

«
...
365
366
367
368
369
...
»

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Brand: Magnetrol Pages: 12

Brand: Magnetrol Pages: 24

Brand: S&C Pages: 28

Brand: S&C Pages: 12

Brand: S&C Pages: 24

Brand: S&C Pages: 24

Brand: S&C Pages: 24

Brand: S&C Pages: 28

Brand: S&C Pages: 37

LMP-1204G-SFP Series

Brand: ANTAIRA Pages: 20

Brand: SMART Pages: 46

Anaconda Switcher VK68A

Brand: X10 Pages: 2

Brand: Paugge Pages: 20

Brand: Samson Pages: 64

Brand: LEGRAND Pages: 140

CEFLA PIR DALIP

Brand: DANLERS Pages: 2

pro-trim PT1000

Brand: Seastar Solutions Pages: 2

Brand: Cypress Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands