manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Configuring for Network Management Applications 

LLDP (Link-Layer Discovery Protocol) 

Also, by using 

show

 commands to access the switch’s neighbor database for 

information collected by an individual switch, system administrators can learn 
about other devices connected to the switch, including  device type 
(capability) and some configuration information. 

LLDP Terminology 

Adjacent Device:

 Refer to “Neighbor or Neighbor Device”. 

Advertisement: 

See LLDPDU. 

Active Port: 

A port linked to another active device (regardless of whether 

STP is blocking the link).  

LLDP: 

Link Layer Discovery Protocol. ProCurve switches are compatible 

with IEEE 802.1AB-2005. 

LLDP-Aware:

 A device that has LLDP in its operating code, regardless of 

whether LLDP is enabled or disabled. 

LLDP Device: 

A switch, server, router, or other device running LLDP. 

LLDP Neighbor:

 An LLDP device that is either directly connected to another 

LLDP device or connected to that device by another, non-LLDP Layer 2 device 
(such as a hub) Note that an 802.1D-compliant switch does not forward LLDP 
data packets even if it is not LLDP-aware. 

LLDPDU (LLDP Data Unit):

 LLDP data packets are transmitted on active 

links and include multiple TLVs containing global and per-port switch 
information. In this guide, LLDPDUs are termed “advertisements” or 
“packets”. 

MIB

 (Management Information Base): An internal database the switch 

maintains for configuration and performance information. 

Neighbor: 

See “LLDP Neighbor”. 

Non_LLDP Device:

 A device that is not capable of LLDP operation. 

TLV (Type-Length-Value): 

A data unit that includes a data type field, a data 

unit length field (in bytes), and a field containing the actual data the unit is 
designed to carry (as an alphanumeric string, a bitmap, or a subgroup of 
information). Some TLVs include subelements that occur as separate data 
points in displays of information maintained by the switch for LLDP 
advertisements. (That is, some TLVs include multiple data points or 
subelements.) 

13-30 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

D-Link SmartPro DGS-1500-20 Reference Manual preview
SmartPro DGS-1500-20
Brand: D-Link Pages: 113
D-Link xStack DGS-3120 Series Cli Reference Manual preview
xStack DGS-3120 Series
Brand: D-Link Pages: 1150
E-T-A 921 Series Instructions For Installation Manual preview
921 Series
Brand: E-T-A Pages: 6
Pathway connectivity solutions 1016 Manual preview
1016
Brand: Pathway connectivity solutions Pages: 2
Qlogic SilverStorm 9000 Hardware Installation Manual preview
SilverStorm 9000
Brand: Qlogic Pages: 50
D-Link DMS-1250 Series Hardware Installation Manual preview
DMS-1250 Series
Brand: D-Link Pages: 38
Vector MZ3-FA-V01 Manual preview
MZ3-FA-V01
Brand: Vector Pages: 6
Yamamoto Electric Works Co., Ltd. MS65F Instruction Manual preview
MS65F
Brand: Yamamoto Electric Works Co., Ltd. Pages: 15
Gilat SkyEdge II-c Capricorn Pro 4 AC Series Installation Notes preview
SkyEdge II-c Capricorn Pro 4 AC Series
Brand: Gilat Pages: 2
Mach Power NW-SP4-001 Installation Manual preview
NW-SP4-001
Brand: Mach Power Pages: 12
WAGO 852-1102 Manual preview
852-1102
Brand: WAGO Pages: 36
Lindy 32 277 Installation And Use Manual preview
32 277
Brand: Lindy Pages: 38
Optical Systems OSD2700F SERIES Operator'S Manual preview
OSD2700F SERIES
Brand: Optical Systems Pages: 29
Black Box LB9007A-SC-R Installation preview
LB9007A-SC-R
Brand: Black Box Pages: 2
NewStar NS-211KA User Manual preview
NS-211KA
Brand: NewStar Pages: 10
H3C S9820-64H Manual preview
S9820-64H
Brand: H3C Pages: 39
NVision NV3128 Instruction Manual preview
NV3128
Brand: NVision Pages: 92
IOGear GUD3C8K2P Quick Start Manual preview
GUD3C8K2P
Brand: IOGear Pages: 10

Brands by name

Popular brands

Load more brands