manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Using the Menu Interface 

Starting and Ending a Menu Session 

Figure 3-1.  The Main Menu with Manager Privileges 

For a description of Main Menu features, see “Main Menu Features” on page 
3-7). 

N o t e    

To configure the switch to start with the menu interface instead of the CLI, go 
to the Manager level prompt in the CLI, enter the 

setup

 command, and in the 

resulting display, change the 

Logon Default

 parameter to 

Menu

. For more 

information, see the 

Installation and Getting Started Guide

 you received 

with the switch. 

How To End a Menu Session and Exit from the Console: 

The method for ending a menu session and exiting from the console depends 
on whether, during the session, you made any changes to the switch configu­
ration that require a switch reboot to activate. (Most changes via the menu 
interface need only a 

Save

, and do not require a switch reboot.) Configuration 

changes needing a reboot are marked with an asterisk (*) next to the config­
ured item in the menu and also next to the 

Switch Configuration

 item in the 

Main Menu. 

3-5 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

OFFICINE OROBICHE PL Series Instruction Manual preview
PL Series
Brand: OFFICINE OROBICHE Pages: 7
3onedata TNS5500D Series Quick Start Manual preview
TNS5500D Series
Brand: 3onedata Pages: 5
3onedata IPS7112G-4GS-8GPOE Quick Installation Manual preview
IPS7112G-4GS-8GPOE
Brand: 3onedata Pages: 3
GarrettCom MAGNUM 6KM Installation And User Manual preview
MAGNUM 6KM
Brand: GarrettCom Pages: 24
Zektor CVS4 User Manual Supplement preview
CVS4
Brand: Zektor Pages: 17
Hirschmann PAT TRS 05 / PATB3 Installation And Setup Manual preview
PAT TRS 05 / PATB3
Brand: Hirschmann Pages: 12
Hama Data Switch Operating Instruction preview
Data Switch
Brand: Hama Pages: 10
StarTech.com MSTCDP122DP Quick Start Manual preview
MSTCDP122DP
Brand: StarTech.com Pages: 2
DeLOCK 87699 User Manual preview
87699
Brand: DeLOCK Pages: 8
3Com 3C17205 - SuperStack 3 Switch 4400 PWR Getting Started Manual preview
3C17205 - SuperStack 3 Switch 4400 PWR
Brand: 3Com Pages: 90
Balluff BNI EIP-950-000-Z009 User Manual preview
BNI EIP-950-000-Z009
Brand: Balluff Pages: 12
RONK VIGILANT VTS0400 Owners & Installation Manual preview
VIGILANT VTS0400
Brand: RONK Pages: 32
Cabletron Systems SEHI SEHI100TX- User Manual preview
SEHI SEHI100TX-
Brand: Cabletron Systems Pages: 75
Network Technologies SE-DVI-2 Installation And Operation Manual preview
SE-DVI-2
Brand: Network Technologies Pages: 7
pro bel VISTEK V1693 User Manual preview
VISTEK V1693
Brand: pro bel Pages: 12
J-Tech Digital JTECH-BS31 User Manual preview
JTECH-BS31
Brand: J-Tech Digital Pages: 12
W2IIHY 3 x 4 SWITCH PLUS Operating Manual preview
3 x 4 SWITCH PLUS
Brand: W2IIHY Pages: 28
3Com 3CRDSF9PWR-US - OfficeConnect Managed Fast Ethernet PoE... User Manual preview
3CRDSF9PWR-US - OfficeConnect Managed Fast Ethernet PoE...
Brand: 3Com Pages: 256

Brands by name

Popular brands

Load more brands