HP ProCurve 2610-24 Management And Configuration Manual Download Page 357

Page: 357 / 464

File Transfers

Transferring Switch Configurations

TFTP: Copying a Configuration File to a Remote Host.

Syntax:

copy < startup-config | running-config > tftp <

ip-addr

> <

remote-file

This command copies the switch’s startup configuration (startup-config file)
to a remote TFTP host.

For example, to upload the current startup configuration to a file named

sw2610

in the configs directory on drive "

" in a remote host having an IP

address of 10.28.227.105:

ProCurve# copy startup-config tftp 10.28.227.105

d:\configs\sw2610

Xmodem: Copying a Configuration File from the Switch to a Serially
Connected PC or Unix Workstation.

To use this method, the switch must

be connected via the serial port to a PC or Unix workstation to which you
want to copy the configuration file. You will need to:

■

Determine a filename to use.

■

Know the directory path you will use to store the the configuration file.

Syntax

copy < startup-config | running-config > xmodem < pc | unix >

For example, to copy a configuration file to a PC serially connected to the
switch:

1. Determine the file name and directory location on the PC.

2. Execute the following command:

ProCurve# copy startup-config xmodem pc

3. After you see the following prompt, press

[Enter]

Press ’Enter’ and start XMODEM on your host...

4. Execute the terminal emulator commands to begin the file transfer.

A-19

Summary of Contents for ProCurve 2610-24
















































































































































































































































































































































































































































































Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands

HP ProCurve 2610-24, Management And Configuration Manual

Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands