manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Port Trunking    

Port Status and Configuration 

ProCurve(config)# int a17 lacp passive 

Error configuring port A17: LACP and port security cannot be run together. 

To restore LACP to the port, you must remove port security and re-enable 
LACP active or passive. 

Changing Trunking Methods.  

To convert a trunk from static to dynamic, 

you must first eliminate the static trunk. 

Static LACP Trunks.  

Where a port is configured for LACP (Active or 

Passive), but does not belong to an existing trunk group, you can add that port 
to a static trunk. Doing so disables dynamic LACP on that port, which means 
you must manually configure both ends of the trunk. 

Dynamic LACP Trunks. 

You can configure a port for LACP-active or LACP-

passive, but on a dynamic LACP trunk you cannot configure the other options 
that you can on static trunks. If you want to manually configure a trunk, use 
the 

trunk

 command. (Refer to “Using the CLI To Configure a Static or Dynamic 

Trunk Group” on page 12-12.) 

VLANs and Dynamic LACP. 

A dynamic LACP trunk operates only in the 

default VLAN (unless you have enabled GVRP on the switch and use 

Forbid

 to 

prevent the ports from joining the default VLAN). 

■

  

If you want to use LACP for a trunk on a non-default VLAN and GVRP is 
disabled, configure the trunk as a static trunk. 

■

  

If there are ports that you do not want on the default VLAN, ensure that 
they cannot become dynamic LACP trunk members.  Otherwise a traffic 
loop can unexpectedly occur. For example: 

VLAN-1 

(Default 

VLAN) 

VLAN-2 

VLAN-1 

(Default 

VLAN) 

VLAN-2 

VLAN-1 

(Default 

VLAN) 

VLAN-2 

VLAN-1 

(Default 

VLAN) 

VLAN-2 

If the ports in VLAN 2 are configured to allow a dynamic trunk (and GVRP is disabled), adding a 
second link in VLAN 2 automatically forms a dynamic LACP trunk and moves the trunk to VLAN-1 
(the default VLAN), which creates a traffic loop in VLAN 1 between the two switches and 
eliminates the link in VLAN 2 between the two switches. 

Figure 12-8.  A Dynamic LACP Trunk Forming in a VLAN Can Cause a Traffic Loop 

12-20 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Cisco Catalyst 3110G Getting Started Manual preview
Catalyst 3110G
Brand: Cisco Pages: 30
Raritan IP-Reach IPR-M1 Specifications preview
IP-Reach IPR-M1
Brand: Raritan Pages: 4
Balluff IO-Link BNI LH1-303-S11-K091 Installation Manual preview
IO-Link BNI LH1-303-S11-K091
Brand: Balluff Pages: 12
Cooper Crouse-Hinds CEAG KO Operating Instructions Manual preview
Crouse-Hinds CEAG KO
Brand: Cooper Pages: 12
Linksys SRW208L Product Data preview
SRW208L
Brand: Linksys Pages: 3
FCI FLT93 Series Installation, Operation, Maintenance And Troubleshooting preview
FLT93 Series
Brand: FCI Pages: 12
A-Neuvideo HD-88CT-A Instruction Manual preview
HD-88CT-A
Brand: A-Neuvideo Pages: 26
TRENDnet TEG-S50TXE SHEETS User Manual preview
TEG-S50TXE SHEETS
Brand: TRENDnet Pages: 20
Crestron CLW-SW1/4RF Operation Manual preview
CLW-SW1/4RF
Brand: Crestron Pages: 36
C&C TECHNIC AVlink VAX-8404F User Manual preview
AVlink VAX-8404F
Brand: C&C TECHNIC Pages: 2
Uponor Smatrix Wave Plus Uahome Module R-167 Installation And Operation Manual preview
Smatrix Wave Plus Uahome Module R-167
Brand: Uponor Pages: 48
QTech QSW-4600 Series Hardware Installation And Reference Manual preview
QSW-4600 Series
Brand: QTech Pages: 58
Little Giant RS-5 Instruction Sheet preview
RS-5
Brand: Little Giant Pages: 8
Black Box IC445A Specifications preview
IC445A
Brand: Black Box Pages: 4
Greengate VNLW-P-1001-MV-N-W Installation Instructions Manual preview
VNLW-P-1001-MV-N-W
Brand: Greengate Pages: 2
xpr TBS Manual preview
TBS
Brand: xpr Pages: 12
Veris Industries Hawkeye 909 Installation Manual preview
Hawkeye 909
Brand: Veris Industries Pages: 2
Tripp Lite B005-HUA4 Owner'S Manual preview
B005-HUA4
Brand: Tripp Lite Pages: 32

Brands by name

Popular brands

Load more brands