manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Interface Access and System Information 

System Information 

Web: Configuring System Parameters 

In the web browser interface, you can enter the following system information: 

■

 

System Name 

■

 

System Location 

■

 

System Contact 

For access to the MAC Age Interval and the Time parameters, use the menu 
interface or the CLI. 

Configure System Parameters in the Web Browser Interface.  

1.  Click on the 

Configuration

 tab. 

2.  Click on 

System Info

. 

3.  Enter the data you want in the displayed fields. 

4.  Implement your new data by clicking on 

Apply Changes

. 

To access the web-based help provided for the switch, click on 

[?]

 in the web 

browser screen. 

7-15 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

IDEC HS5L Series Instruction Sheet preview
HS5L Series
Brand: IDEC Pages: 8
IDEM SAFETY SWITCHES MPR Operating Instructions preview
MPR
Brand: IDEM SAFETY SWITCHES Pages: 2
Raritan PARAGON II Series Quick Manual preview
PARAGON II Series
Brand: Raritan Pages: 1
Raritan Paragon Manager Installation And Operation Manual preview
Paragon Manager
Brand: Raritan Pages: 117
LONG-JOIN JL-403C Manual preview
JL-403C
Brand: LONG-JOIN Pages: 2
SIIG AV-GM08G3-S1 Manual preview
AV-GM08G3-S1
Brand: SIIG Pages: 17
H3C S12500G-AF Series Installation Manual preview
S12500G-AF Series
Brand: H3C Pages: 105
G&D DVIMUX8-USB Installation And Operation Manual preview
DVIMUX8-USB
Brand: G&D Pages: 80
Microsonic zws-7/CD/QS Operating Instructions preview
zws-7/CD/QS
Brand: Microsonic Pages: 2
Belkin F1DF102P Quick Installation Manual preview
F1DF102P
Brand: Belkin Pages: 40
NTI UNIMUX-DVI-2 Installation And Operation Manual preview
UNIMUX-DVI-2
Brand: NTI Pages: 15
S&T kontron KSwitch D1 UGPD User Manual preview
kontron KSwitch D1 UGPD
Brand: S&T Pages: 40
LEGRAND Pro 21 7756 28 Manual preview
Pro 21 7756 28
Brand: LEGRAND Pages: 197
Valcom V-2971 Connections preview
V-2971
Brand: Valcom Pages: 1
IBM 8265 Nways ATM Switch Product Description preview
8265 Nways ATM Switch
Brand: IBM Pages: 100
QTech QSW-4600 Series Hardware Installation And Reference Manual preview
QSW-4600 Series
Brand: QTech Pages: 58
Santon D1-G/H-T Installation Manual preview
D1-G/H-T
Brand: Santon Pages: 16
Stahl 8537/2 Operating Instructions Manual preview
8537/2
Brand: Stahl Pages: 28

Brands by name

Popular brands

Load more brands