manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Time Protocols 

SNTP Unicast Time Polling with Multiple SNTP Servers 

Disabling the TimeP Mode. 

Disabling the TimeP mode means to configure 

it as disabled. (Disabling TimeP prevents the switch from using it as the time 
synchronization protocol, even if it is the selected 

Time Sync Method 

option.) 

Syntax

: 

no ip timep 

Disables TimeP by changing the TimeP mode 
configuration to 

Disabled

. 

For example, if the switch is running TimeP in DHCP mode, 

no ip timep

 changes 

the TimeP configuration as shown below, and disables time synchronization 
on the switch. 

Even though the Time Sync Mode is set to Timep, 
time synchronization is disabled because no ip 
timep has disabled the TimeP Mode parameter. 

Figure 9-15.  Example of Disabling Time Synchronization by Disabling the TimeP 
Mode Parameter 

SNTP Unicast Time Polling with Multiple 
SNTP Servers 

When running SNTP unicast time polling as the time synchronization method, 
the switch requests a time update from the server you configured with either 
the Server Address parameter in the menu interface, or the primary server in 
a list of up to three SNTP servers configured using the CLI. If the switch does 
not receive a response from the primary server after three consecutive polling 
intervals, the switch tries the next server (if any) in the list. If the switch tries 
all servers in the list without success, it sends an error message to the Event 
Log and reschedules to try the address list again after the configured 

Poll Interval 

time has expired. 

Address Prioritization 

If you use the CLI to configure multiple SNTP servers, the switch prioritizes 
them according to the decimal values of their IP addresses. That is, the switch 
compares the decimal value of the octets in the addresses and orders them 

9-21 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

D-Link xStack DGS-3612G series Reference Manual preview
xStack DGS-3612G series
Brand: D-Link Pages: 546
D-Link xStack DGS-3400 Series User Manual preview
xStack DGS-3400 Series
Brand: D-Link Pages: 326
D-Link xStack DGS-3612G series Cli Manual preview
xStack DGS-3612G series
Brand: D-Link Pages: 493
D-Link xStack DGS-3400 Series Cli Reference Manual preview
xStack DGS-3400 Series
Brand: D-Link Pages: 540
D-Link DXS-3326GSR - xStack Switch - Stackable Reference Manual preview
DXS-3326GSR - xStack Switch - Stackable
Brand: D-Link Pages: 354
D-Link EasySmart DGS-1100-08 Manual preview
EasySmart DGS-1100-08
Brand: D-Link Pages: 44
pathway 7748 Manual preview
7748
Brand: pathway Pages: 28
GE T1000 Technical Manual preview
T1000
Brand: GE Pages: 302
Brightlink 16x16 Manual preview
16x16
Brand: Brightlink Pages: 33
FLIR ACCDPS281B Quick Start Manual preview
ACCDPS281B
Brand: FLIR Pages: 2
Grizzly H8239 Instructions preview
H8239
Brand: Grizzly Pages: 2
QCT QuantaMesh T4000 Series Installation Manual preview
QuantaMesh T4000 Series
Brand: QCT Pages: 41
NETGEAR GS316P Installation Manual preview
GS316P
Brand: NETGEAR Pages: 8
ATEN 4719264645624 User Manual preview
4719264645624
Brand: ATEN Pages: 261
Festo SMT-8-...-B Series Manual preview
SMT-8-...-B Series
Brand: Festo Pages: 2
IN-COMMAND NCSTS9 Installation And Operation Manual preview
NCSTS9
Brand: IN-COMMAND Pages: 8
Myson Touch 2 WiFi Leaflet preview
Touch 2 WiFi
Brand: Myson Pages: 2
ATEN Altusen KN9008 User Manual preview
Altusen KN9008
Brand: ATEN Pages: 178

Brands by name

Popular brands

Load more brands