manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Configuring for Network Management Applications 

LLDP (Link-Layer Discovery Protocol) 

Enabling CDP Operation. 

Enabling CDP operation (the default) on the 

switch causes the switch to add entries to its CDP Neighbors table for any 
CDP packets it receives from other neighboring CDP devices. 

Disabling CDP Operation. 

Disabling CDP operation clears the switch’s 

CDP Neighbors table and causes the switch to drop inbound CDP packets 
from other devices without entering the data in the CDP Neighbors table. 

Syntax: 

[no] cdp run 

Enables or disables read-only CDP operation on the switch. 
(Default: Enabled) 

For example, to disable CDP read-only operation on the switch: 

ProCurve(config)# no cdp run 

When CDP is disabled: 

■

 

show cdp neighbors

 displays an empty CDP Neighbors table 

■

 

show cdp

 displays 

Global CDP information
  Enable CDP [Yes]: No

Enabling or Disabling CDP Operation on Individual Ports.  

In the 

factory-default configuration, the switch has all ports enabled to receive CDP 
packets. Disabling CDP on a port causes it to drop inbound CDP packets 
without recording their data in the CDP Neighbors table. 

Syntax

: 

[no] cdp enable < [e] port-list > 

For example, to disable CDP on port A1: 

ProCurve(config)# no cdp enable a1 

13-58 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

ABLE 6 Series Installation & Maintenance Instructions preview
6 Series
Brand: ABLE Pages: 5
FELA SWITCH CASAMBI Operation And Installation Manual preview
SWITCH CASAMBI
Brand: FELA Pages: 13
H3C Mini Series Manual preview
Mini Series
Brand: H3C Pages: 17
Panio HW2250K User Manual preview
HW2250K
Brand: Panio Pages: 5
Lindy 32351 Manual preview
32351
Brand: Lindy Pages: 70
Baxall DVS24 Installation And Operating Instructions Manual preview
DVS24
Brand: Baxall Pages: 33
WAGO ETHERNET Accessories 852 852-0111 Mounting, Installation And Handling Manual preview
ETHERNET Accessories 852 852-0111
Brand: WAGO Pages: 38
LevelOne FEP-0800 Quick Installation Manual preview
FEP-0800
Brand: LevelOne Pages: 17
REV Ritter RF102R Assembly And Operating Instructions Manual preview
RF102R
Brand: REV Ritter Pages: 15
Paugge ENT-MX20B16X16 User Manual preview
ENT-MX20B16X16
Brand: Paugge Pages: 20
Phoenix Contact FL SWITCH SFN 16TX Installation Notes For Electricians preview
FL SWITCH SFN 16TX
Brand: Phoenix Contact Pages: 6
ADS Antenna-Disconnect-Switch Assembly And Operation Manual preview
Antenna-Disconnect-Switch
Brand: ADS Pages: 12
LINK-MI LM-MX42-AUDIO User Manual preview
LM-MX42-AUDIO
Brand: LINK-MI Pages: 12
TCi 13811 Installation Manual preview
13811
Brand: TCi Pages: 11
WilTec SKD-1 Operation Manual preview
SKD-1
Brand: WilTec Pages: 7
Festo SMT-8-...-B Series Manual preview
SMT-8-...-B Series
Brand: Festo Pages: 2
Intellinet 560757 User Manual preview
560757
Brand: Intellinet Pages: 12
Justin JH-810 User Manual preview
JH-810
Brand: Justin Pages: 8

Brands by name

Popular brands

Load more brands