manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Troubleshooting 

Using Logging To Identify Problem Sources 

Debug and Syslog Operation 

You can direct switch debug (Event log) messages to these destinations: 

■

  

Up to six SyslogD servers 

■

  

One management-access session through: 

•   A direct-connect RS-232 console CLI session 

•   A Telnet session 

•   An SSH session 

Figure C-8.  Example of Debug Output to a Console CLI Session 

Debug logging requires a logging destination (SyslogD server and/or a session 
type), and involves the 

logging

 and 

debug destination

 commands. Actions you 

can perform with Debug and Syslog operation include: 

■

  

Configure the switch to send Event Log messages to one or more SyslogD 
servers. Included is the option to send the messages to the 

user

 log facility 

(default) on the configured servers, or to another log facility. 

■

  

Configure the switch to send Event Log messages to the current manage­
ment-access session (serial-connect CLI, Telnet CLI, or SSH). 

■

  

Disable all Syslog debug logging while retaining the Syslog addresses from 
the switch configuration. This allows you to configure Syslog messaging 
and then disable and re-enable it as needed. 

■

  

Display the current debug configuration. If Syslog logging is currently 
active, this includes the Syslog server list. 

■

  

Display the current Syslog server list when Syslog logging is disabled. 

C-25 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Magnetrol T20 Series Instruction Manual And Replacement Parts List preview
T20 Series
Brand: Magnetrol Pages: 12
Magnetrol T20 Series Installation And Operating Manual preview
T20 Series
Brand: Magnetrol Pages: 24
Balluff BNI IOL-314-S52-P012 Assembly Instructions Manual preview
BNI IOL-314-S52-P012
Brand: Balluff Pages: 22
Danfoss LLS 4000 Installation Manual preview
LLS 4000
Brand: Danfoss Pages: 6
Manhattan 160605 Quick Start Manual preview
160605
Brand: Manhattan Pages: 2
Eaton HOMECT Installation And Setup Manual preview
HOMECT
Brand: Eaton Pages: 5
Eaton ATR Series Instruction Leaflet preview
ATR Series
Brand: Eaton Pages: 2
Hisselektronik Safeline 2000 Light Manual For Programmering preview
Safeline 2000 Light
Brand: Hisselektronik Pages: 9
Cabletron Systems SmartSwitch SBU128 User Manual preview
SmartSwitch SBU128
Brand: Cabletron Systems Pages: 76
JetNet 5018G Series Quick Installation Manual preview
5018G Series
Brand: JetNet Pages: 20
Cypress SE-DVI-8-LC Operation Manual preview
SE-DVI-8-LC
Brand: Cypress Pages: 4
Atlona AT-HD-SC-500 Manual preview
AT-HD-SC-500
Brand: Atlona Pages: 22
MicroNet SP684C User Manual preview
SP684C
Brand: MicroNet Pages: 74
Thorn SENSALINK SENLSS V2 Installation And Commissioning Instructions preview
SENSALINK SENLSS V2
Brand: Thorn Pages: 2
H-Tronic WPS 3000 Manual preview
WPS 3000
Brand: H-Tronic Pages: 20
Accton Technology 24/48 10/100 Ports + 2GE Management Manual preview
24/48 10/100 Ports + 2GE
Brand: Accton Technology Pages: 512
LevelOne GEL-1072 Brochure & Specs preview
GEL-1072
Brand: LevelOne Pages: 4
N-Tron 509FX Specification Sheet preview
509FX
Brand: N-Tron Pages: 2

Brands by name

Popular brands

Load more brands