HP ProCurve 2610-24 Management And Configuration Manual Download Page 137

Page: 137 / 464

Interface Access and System Information

Interface Access: Console/Serial Link, Web, and Telnet

CLI: Modifying the Interface Access

Interface Access Commands Used in This Section

show console

below

[no] telnet-server

below

[no] web-management

page 7-6

console

page 7-6

local terminal mode

page 7-8

Listing the Current Console/Serial Link Configuration.

The following

command lists the current interface access parameter settings.

Syntax

show console

This example shows the switch’s default console/serial configuration.

Interface Access
Enable/Disable

Console Control
Options

Event Log Event
Types To List

Figure 7-2. Listing of Show Console Command

Reconfigure Inbound Telnet Access.

In the default configuration,

inbound Telnet access is enabled.

Syntax

[no] telnet-server

To disable inbound Telnet access:

ProCurve(config)# no telnet-server

To re-enable inbound Telnet access:

ProCurve(config)# telnet-server

7-5

Summary of Contents for ProCurve 2610-24
















































































































































































































































































































































































































































































Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands

HP ProCurve 2610-24, Management And Configuration Manual

Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands