HP ProCurve 2610-24 Management And Configuration Manual Download Page 201

Page: 201 / 464

Port Status and Basic Configuration

Viewing Port Status and Configuring Port Parameters

■

show interface config

: Lists a subset of the data shown by the

show

interfaces

command (above); that is, only the enabled/disabled, mode, and

flow control status for all ports on the switch.

Syntax

show interfaces [ brief | config ]

These two commands display the information listed in
table 10-2, below.

Table 10-2. Comparing the "Show Interfaces” Command Options*

Feature

Show Interfaces Brief Show Interfaces Config

Port Number and Type

Yes

Enabled Y/N

Yes

Flow Control

Yes

Status Up/Down

Yes

Mode (Operating)

Yes

Intrusion Alert

Yes

Mode (Configured)

Yes

MDIX Mode

Operating

Configured

* There is also the

show interfaces [[e] <

port-number

option, which displays

port statistics. Refer to “Viewing Port and Trunk Group Statistics and Flow
Control Status” on page B-10.

The figure 10-3 shows an example of the output of the

show interface brief

command.

ProCurve(config)# show interfaces brief

Status and Counters - Port Status

Current Operating Mode

| Intrusion

MDI Flow Bcast

Port Type | Alert Enabled Status Mode Mode Ctrl Limit
----- --------- + --------- ------- ------ ---------- ----- ----- ------

10/100TX | No

Yes

10FDx MDI off

10/100TX | No

Yes

Down

10FDx MDI off

10/100TX | No

Yes

Down

10FDx MDI off

10/100TX | No

Yes

Down

10FDx MDIX off

10/100TX | No

Yes

Down

10FDx MDIX off

10/100TX | No

Yes

Down

10FDx MDI off

10/100TX | No

Yes

Down

10FDx MDI off

Figure 10-3. Example Show Interface Brief Command Listing

10-9

Summary of Contents for ProCurve 2610-24
















































































































































































































































































































































































































































































Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands

HP ProCurve 2610-24, Management And Configuration Manual

Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands