manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

File Transfers 

Downloading Switch Software 

General System Information 

b.   Check the 

Firmware revision 

line. 

CLI: Switch-To-Switch Downloads 

You can download a switch software file between two switches that use the 
same code base and which are connected on your LAN. To do so, use a 

copy 

tftp

 command from the destination switch.The options for this CLI feature 

include: 

■

  

Copy from primary flash in the source to either primary or secondary in 
the destination. 

■

  

Copy from either primary or secondary flash in the source to either 
primary or secondary flash in the destination. 

Downloading from Primary Only.  

This command (executed in the destina­

tion switch) downloads the switch software from the source switch’s primary 
flash to either the primary or secondary flash in the destination switch. 

Syntax

:  

copy tftp flash < 

ip-addr 

> flash [primary | secondary] 

If you do not specify either a primary or secondary flash location for the 
destination, the download automatically goes to primary flash. 

For example, to download switch software from primary flash in a switch with 
an IP address of 10.28.227.103 to the primary flash in the destination switch, 
you would execute the following command in the destination switch’s CLI: 

Running Total 
of Bytes 
Downloaded 

Figure A-5.   Switch-To-Switch, from Primary in Source to Either Flash in 

Destination 

Downloading from Either Flash in the Source Switch to Either Flash 
in the Destination Switch.  

This command (executed in the destination 

switch) gives you the most options for downloading between switches. 

Syntax

: 

copy tftp flash < 

ip-addr 

> < /os/primary > | < /os/secondary > 

[primary | secondary] 

A-15 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

C&H Technologies M221 Specifications preview
M221
Brand: C&H Technologies Pages: 1
D-Box G3 Installation Manual preview
G3
Brand: D-Box Pages: 31
Cabletron Systems SmartSwitch 9A100 Installation And Setup Manual preview
SmartSwitch 9A100
Brand: Cabletron Systems Pages: 52
Cabletron Systems SmartSwitch 9W006 Quick Start Manual preview
SmartSwitch 9W006
Brand: Cabletron Systems Pages: 34
Cabletron Systems SmartSTACK ELS100-S24TX2M Management Manual preview
SmartSTACK ELS100-S24TX2M
Brand: Cabletron Systems Pages: 102
Cabletron Systems 9A426-01 Appendix preview
9A426-01
Brand: Cabletron Systems Pages: 24
Cabletron Systems SmartSwitch 9000 Appendix preview
SmartSwitch 9000
Brand: Cabletron Systems Pages: 14
Cabletron Systems MicroMMAC 22ES Reference Manual preview
MicroMMAC 22ES
Brand: Cabletron Systems Pages: 38
CZHOON CZH-T287 User Manual preview
CZH-T287
Brand: CZHOON Pages: 4
F&G PM 3 FG Series Installation Instructions Manual preview
PM 3 FG Series
Brand: F&G Pages: 6
Samson 4747 Mounting And Operating Instructions preview
4747
Brand: Samson Pages: 64
Bridgetek PANL PH44 Quick Start Manual preview
PANL PH44
Brand: Bridgetek Pages: 2
H3C S5120-EI Series Configuration Commands preview
S5120-EI Series
Brand: H3C Pages: 29
Canoga Perkins HS8000 Quick Start Manual preview
HS8000
Brand: Canoga Perkins Pages: 7
GarrettCom PS14H-48VDC Installation And User Manual preview
PS14H-48VDC
Brand: GarrettCom Pages: 77
Cabletron Systems SmartStack STS16-20R Installation And User Manual preview
SmartStack STS16-20R
Brand: Cabletron Systems Pages: 258
SmartAVI D2H-4P Quick Start Manual preview
D2H-4P
Brand: SmartAVI Pages: 2
IPGARD SDPN-2D Manual preview
SDPN-2D
Brand: IPGARD Pages: 15

Brands by name

Popular brands

Load more brands