manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Troubleshooting 

Using Logging To Identify Problem Sources 

Shows that Syslog (Destination) logging is 
enabled and transmitting log messages to IP 
address 18.120.38.155. Also shows that the 
logging facility is set to 

user

 (the default), and 

that session logging is enabled.) 

Disables Syslog logging (but retains the 
Syslog IP address in the switch 
configuration). Does not affect Session 
logging. 

Shows Syslog (Destination) logging now 
disabled. Session logging continues to 
operate. 

Figure C-10. Example of Disabling Syslog Operation 

Viewing Debug (Syslog and Session) Status.  

Use these commands to 

determine the current debug configuration and status: 

Syntax

: 

show < config | running > 

Lists the current startup-config or running-config file, with 
any currently configured IP addresses for SyslogD servers. 

ProCurve(config)# show config 

Startup configuration: 

; J9085A Configuration Editor; Created on release #R.11.XX 

hostname “ProCurve switch” 
ip default-gateway 18.38.222.1
logging 18.120.38.155
logging 18.120.43.125 

vlan 1
   name “DEFAULT-VLAN” 

snmp-server community “public” Unrestricted 

The configured Syslog server IP 
addresses appear in the switch’s 
configuration file, even if Syslog 
logging is disabled. 

Figure C-11. Example of Show Config Output with SyslogD Servers Configured 

C-30 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Hama 11800 Operating Instruction preview
11800
Brand: Hama Pages: 5
3Com SuperStack 3 4900 Datasheet preview
SuperStack 3 4900
Brand: 3Com Pages: 2
Raritan IP-Reach IPR-M1 Specifications preview
IP-Reach IPR-M1
Brand: Raritan Pages: 4
Intermatic T7802BC Supplementary Manual preview
T7802BC
Brand: Intermatic Pages: 1
Ableconn USBCHUB4A User Manual preview
USBCHUB4A
Brand: Ableconn Pages: 16
NETGEAR ProSafe GS104 Installation Manual preview
ProSafe GS104
Brand: NETGEAR Pages: 8
ATEN KVMP CS1782A Quick Start Manual preview
KVMP CS1782A
Brand: ATEN Pages: 2
StarTech.com 8STSV231DDVDUA Manual preview
8STSV231DDVDUA
Brand: StarTech.com Pages: 16
Endress+Hauser Nivotester FTC325 Instruction Manual preview
Nivotester FTC325
Brand: Endress+Hauser Pages: 40
Penguin Computing Arctica 1600cs Installation Manual preview
Arctica 1600cs
Brand: Penguin Computing Pages: 71
N-Tron 702-W Features preview
702-W
Brand: N-Tron Pages: 2
Fore Systems forerunner series Configuration Manual preview
forerunner series
Brand: Fore Systems Pages: 352
SEKURYX CK4-HPD404C User Manual preview
CK4-HPD404C
Brand: SEKURYX Pages: 13
TDT ACO32 Hardware Reference Manual preview
ACO32
Brand: TDT Pages: 21
Audioplex INW-8 Installation Manual preview
INW-8
Brand: Audioplex Pages: 8
Woodward MPU Manual preview
MPU
Brand: Woodward Pages: 20
Hama 00039859 User Manual preview
00039859
Brand: Hama Pages: 3
MSD 8956 Installation Instructions preview
8956
Brand: MSD Pages: 4

Brands by name

Popular brands

Load more brands