manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

E 

Daylight Savings Time on ProCurve Switches 

Configuring Daylight Savings Time 

This information applies to the following ProCurve switches: 

•  2512 

•  2824 

•  1600M 

•  ProCurve 

•  2524 

•  2848 

•  2400M 

AdvanceStack 

•  2610 

•  3400cl 

•  2424M 

Switches 

•  2610-PWR  •  4108gl 

•  4000M 

•  ProCurve 

AdvanceStack Routers 

•  2626 

•  4104gl 

•  8000M 

•  2650 

•  6108 

•  212M 

•  2626-PWR  •  5304xl 

•  224M 

•  2650-PWR  •  5308xl 

•  5400zl 
•  8200zl 

ProCurve switches provide a way to automatically adjust the system clock for 
Daylight Savings Time (DST) changes.  To use this feature you define the 
month and date to begin and to end the change from standard time.  In addition 
to the value "none" (no time changes), there are five pre-defined settings, 
named: 

■

 

Alaska 

■

 

Canada and Continental US 

■

 

Middle Europe and Portugal 

■

 

Southern Hemisphere 

■

 

Western Europe 

The pre-defined settings follow these rules: 

Alaska: 

• 

Begin DST at 2am on the second Sunday in March. 

• 

End DST at 2am on the first Sunday in November. 

E-1 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

NETGEAR DS104 Installation Manual preview
DS104
Brand: NETGEAR Pages: 15
H3C S9500E Series Connecting Manual preview
S9500E Series
Brand: H3C Pages: 13
H3C S9500E Series Security Configuration Manual preview
S9500E Series
Brand: H3C Pages: 207
H3C S3100-52P Operation Manual preview
S3100-52P
Brand: H3C Pages: 62
Meridian SX-4FX Series Installation & Operation Instructions preview
SX-4FX Series
Brand: Meridian Pages: 16
LevelOne Infinity IES-1881 Quick Installation Manual preview
Infinity IES-1881
Brand: LevelOne Pages: 2
Enterasys Matrix DFE-Gold 4G4202-60 Hardware Installation Manual preview
Matrix DFE-Gold 4G4202-60
Brand: Enterasys Pages: 78
ZENEC 2E-AVS Instruction Manual preview
2E-AVS
Brand: ZENEC Pages: 16
KCC KTD-600 Series Manual preview
KTD-600 Series
Brand: KCC Pages: 6
Icy Box IB-AC618 Manual preview
IB-AC618
Brand: Icy Box Pages: 6
CTS FOS-3124 SERIES User Manual preview
FOS-3124 SERIES
Brand: CTS Pages: 223
steute Ex 355 Mounting And Wiring Instructions preview
Ex 355
Brand: steute Pages: 20
Minicom Smart 4 User Manual preview
Smart 4
Brand: Minicom Pages: 16
Pilz 506401 Operating Manual preview
506401
Brand: Pilz Pages: 20
National Instruments SCXI-1130 Getting Started Manual preview
SCXI-1130
Brand: National Instruments Pages: 23
Subject Link RPT-2012/P-4F-T-1 Series Hardware Installation Manual preview
RPT-2012/P-4F-T-1 Series
Brand: Subject Link Pages: 2
Murphy EVS-2 Installation And Operation Manual preview
EVS-2
Brand: Murphy Pages: 24
ALFAtron MUH88E User Manual preview
MUH88E
Brand: ALFAtron Pages: 45

Brands by name

Popular brands

Load more brands