manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

File Transfers 

Troubleshooting TFTP Downloads 

Troubleshooting TFTP Downloads 

When using the menu interface, if a TFTP download fails, the Download OS 
screen indicates the failure. 

Message Indicating 
cause of TFTP Download 
Failure 

Figure A-7.  Example of Message for Download Failure 

To find more information on the cause of a download failure, examine the 
messages in the switch’s Event Log by executing this CLI command: 

ProCurve# show log tftp 

(For more on the Event Log, see “Using Logging To Identify Problem Sources” 
on page C-21.) 

Some of the causes of download failures include: 

■

  

Incorrect or unreachable address specified for the 

TFTP Server

 parameter. 

This may include network problems. 

■

  

Incorrect VLAN. 

■

  

Incorrect name specified for the 

Remote File Name 

parameter, or the 

specified file cannot be found on the TFTP server. This can also occur if 
the TFTP server is a Unix machine and the case (upper or lower) for the 
filename on the server does not match the case for the filename entered 
for the 

Remote File Name 

parameter in the Download OS screen. 

■

  

One or more of the switch’s IP configuration parameters are incorrect. 

A-17 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

3Com Switch 4500 Family Configuration Manual preview
Switch 4500 Family
Brand: 3Com Pages: 742
3Com Switch 7757 Configuration Manual preview
Switch 7757
Brand: 3Com Pages: 940
3Com 4210 Series Release Notes preview
4210 Series
Brand: 3Com Pages: 43
3Com OfficeConnect WX1200 Command Reference Manual preview
OfficeConnect WX1200
Brand: 3Com Pages: 646
Balluff BNI IOL-727-S51-P012 Assembly Instructions Manual preview
BNI IOL-727-S51-P012
Brand: Balluff Pages: 20
Eaton NR Installation And Operation Instructions Manual preview
NR
Brand: Eaton Pages: 12
H3C S9820-64H Installation Manual preview
S9820-64H
Brand: H3C Pages: 55
H3C S7508E-X Installation Manual preview
S7508E-X
Brand: H3C Pages: 111
H3C S7500X Series Interface Configuration Manual preview
S7500X Series
Brand: H3C Pages: 34
H3C S6890 Series Configuration Examples preview
S6890 Series
Brand: H3C Pages: 47
H3C S6800 Series Configuration Examples preview
S6800 Series
Brand: H3C Pages: 8
H3C S5830 Series Troubleshooting Manual preview
S5830 Series
Brand: H3C Pages: 47
H3C S5810 Series Quick Start preview
S5810 Series
Brand: H3C Pages: 4
H3C S5560X-EI Series Configuration Manual preview
S5560X-EI Series
Brand: H3C Pages: 63
H3C S5560X-EI Series Installation Manual preview
S5560X-EI Series
Brand: H3C Pages: 89
H3C S3100V2 Series Installation, Quick Start preview
S3100V2 Series
Brand: H3C Pages: 3
H3C S12500G-AF Series Troubleshooting Manual preview
S12500G-AF Series
Brand: H3C Pages: 86
H3C S12500-X Installation Manual preview
S12500-X
Brand: H3C Pages: 168

Brands by name

Popular brands

Load more brands