manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Using the Command Line Interface (CLI) 

CLI Control and Editing 

CLI Control and Editing 

Keystrokes 

Function 

[Ctrl] [A] 

Jumps to the first character of the command line. 

[Ctrl] [B]

 or 

[<]

 

Moves the cursor back one character. 

[Ctrl] [C] 

Terminates a task and displays the command prompt. 

[Ctrl] [D] 

Deletes the character at the cursor. 

[Ctrl] [E] 

Jumps to the end of the current command line. 

[Ctrl] [F]

 or 

[>]

 

Moves the cursor forward one character. 

[Ctrl] [K] 

Deletes from the cursor to the end of the command line. 

[Ctrl] [L]

 or 

[Ctrl] [R] 

Repeats current command line on a new line. 

[Ctrl] [N]

 or 

[v]

 

Enters the next command line in the history buffer. 

[Ctrl] [P]

 or 

[^]

 

Enters the previous command line in the history buffer. 

[Ctrl] [U]

 or 

[Ctrl] [X] 

Deletes from the cursor to the beginning of the command line. 

[Ctrl] [W] 

Deletes the last word typed. 

[Esc] [B] 

Moves the cursor backward one word. 

[Esc] [D] 

Deletes from the cursor to the end of the word. 

[Esc] [F] 

Moves the cursor forward one word. 

[Delete]

 or 

Deletes the first character to the left of the cursor in the command 

[

Backspace] 

line. 

4-16 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Hama S2100 Manual preview
S2100
Brand: Hama Pages: 9
LEGRAND WZ3RL10 Installation Instructions preview
WZ3RL10
Brand: LEGRAND Pages: 2
Maipu MyPower S2300-28TC-AC Installation Manual preview
MyPower S2300-28TC-AC
Brand: Maipu Pages: 31
Maiwe MIEN2208 Series User Manual preview
MIEN2208 Series
Brand: Maiwe Pages: 5
Vega VEGAWAVE S 61 Operating Instructions Manual preview
VEGAWAVE S 61
Brand: Vega Pages: 44
Radware Alteon 5208 Memory Upgrade Procedure preview
Alteon 5208
Brand: Radware Pages: 4
Cypress CLUX-C61C Operation Manual preview
CLUX-C61C
Brand: Cypress Pages: 16
TRENDnet TEG-S41SX Specifications preview
TEG-S41SX
Brand: TRENDnet Pages: 2
BZB Gear BG-UHD44MA User Manual preview
BG-UHD44MA
Brand: BZB Gear Pages: 27
Eaton Cutler-Hammer NTV Series Instruction Bulletin preview
Cutler-Hammer NTV Series
Brand: Eaton Pages: 28
ATEN UC2322 User Manual preview
UC2322
Brand: ATEN Pages: 16
Rosewill RC-410LX User Manual preview
RC-410LX
Brand: Rosewill Pages: 10
A-Neuvideo ANI-8X2MFS Instruction Manual preview
ANI-8X2MFS
Brand: A-Neuvideo Pages: 44
ADDER ADDERView Secure AVS-4128 Quick Start preview
ADDERView Secure AVS-4128
Brand: ADDER Pages: 2
ADDER ADDERView CCS-MV4228 Quick Start preview
ADDERView CCS-MV4228
Brand: ADDER Pages: 2
ADDER ADDERView CCS-MV4224 User Manual preview
ADDERView CCS-MV4224
Brand: ADDER Pages: 6
Tripp Lite N252-024-6A-SH Installation Manual preview
N252-024-6A-SH
Brand: Tripp Lite Pages: 8
ITC T-6713 Operation Manual preview
T-6713
Brand: ITC Pages: 11

Brands by name

Popular brands

Load more brands