HP ProCurve 2610-24 Management And Configuration Manual Download Page 143

Page: 143 / 464

Interface Access and System Information

System Information

Time Zone:

The number of minutes your time zone location is to the

West (-) or East (+) of Coordinated Universal Time (formerly GMT). The
default

means no time zone is configured. For example, Berlin, Germany is

in the +1 zone, while Vancouver, Canada is in the -8 zone.

Daylight Time Rule:

Specifies the daylight savings time rule to apply for your

location. The default is

None

. (For more on this topic, see Appendix E,

“Daylight Savings Time on ProCurve Switches.)

Time:

Used in the CLI to specify the time of day, the date, and other system

parameters.

Menu: Viewing and Configuring System Information

To access the system information parameters:

1. From the Main Menu, Select...

2. Switch Configuration...

1. System Information

System Information

Figure 7-6. The System Information Configuration Screen (Default Values)

N o t e

To help simplify administration, it is recommended that you configure

System Name

to a character string that is meaningful within your system.

2. Press

[E]

(for Edit). The cursor moves to the

System Name

field.

7-11

Summary of Contents for ProCurve 2610-24
















































































































































































































































































































































































































































































Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands

HP ProCurve 2610-24, Management And Configuration Manual

Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands