manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Configuring for Network Management Applications 

LLDP (Link-Layer Discovery Protocol) 

Syntax 

[ no ] lldp config < 

port-list 

> basicTlvEnable < 

TLV-Type

 > 

port_descr 

For outbound LLDP advertisements, includes an 
alphanumeric string describing the port. 

system_name 

For outbound LLDP advertisements, includes the system’s 
assigned name. 

system_descr 

For outbound LLDP advertisements, includes an 
alphanumeric string describing the full name and version 
identification for the system’s hardware type, software 
version, and networking application. 

system_cap 

For outbound advertisements, includes a bitmask of 
system capabilities (device functions) that are supported. 
Also includes information on whether the capabilities are 
enabled. 

For example, if you wanted to exclude the system name from the outbound 
LLDP advertisements for all ports on a 2626 switch, you would use this 
command: 

ProCurve(config)# no lldp config 1-26 basicTlvEnable  

system_name 

If you later decided to reinstate the system name on ports 1-5, you would use 
this command: 

ProCurve(config)# lldp config 1-5 basicTlvEnable  

system_name 

Displaying Advertisement Data 

Command 

Page 

show lldp info local-device 

below 

show lldp info remote-device 

13-47 

show lldp info stats 

13-50 

13-45 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

D-Link DKVM-IP1 Manual preview
DKVM-IP1
Brand: D-Link Pages: 73
SMC Networks PF2MC7 Series Operation Manual preview
PF2MC7 Series
Brand: SMC Networks Pages: 102
Penguin Edge RTM-ATCA-F140 Quick Start Manual preview
Edge RTM-ATCA-F140
Brand: Penguin Pages: 2
CYP CDPS-UA6H2HFS Operation Manual preview
CDPS-UA6H2HFS
Brand: CYP Pages: 32
RONK VIGILANT VTS0400 Owners & Installation Manual preview
VIGILANT VTS0400
Brand: RONK Pages: 32
Hall Research Technologies Genesis Digital HSM-04-02 User Manual preview
Genesis Digital HSM-04-02
Brand: Hall Research Technologies Pages: 28
G&D ControlCenter-IP-XS Installation Manual preview
ControlCenter-IP-XS
Brand: G&D Pages: 56
QTech QSW-4600 Series Hardware Installation And Reference Manual preview
QSW-4600 Series
Brand: QTech Pages: 58
Gefen HDMI-242 User Manual preview
HDMI-242
Brand: Gefen Pages: 12
HB Products HBSC2-SSR Instruction Manual preview
HBSC2-SSR
Brand: HB Products Pages: 6
Videosec RF-ZE901-220 Installation Manual preview
RF-ZE901-220
Brand: Videosec Pages: 3
EMP-Centauri T1/1+1ENP8dB-1 Instruction Manual preview
T1/1+1ENP8dB-1
Brand: EMP-Centauri Pages: 4
KinAn XL1704 User Manual preview
XL1704
Brand: KinAn Pages: 8
Scion-Tech SC04.1404 Operating Instructions Manual preview
SC04.1404
Brand: Scion-Tech Pages: 16
Primewire 302523/20191008SZ114 User Manual preview
302523/20191008SZ114
Brand: Primewire Pages: 12
Zigen hxl-88 User Manual preview
hxl-88
Brand: Zigen Pages: 72
NIVELCO NIVOMAG MK-21 Series User Manual preview
NIVOMAG MK-21 Series
Brand: NIVELCO Pages: 2
Cabletron Systems MicroMMAC-24E Installation Manual preview
MicroMMAC-24E
Brand: Cabletron Systems Pages: 83

Brands by name

Popular brands

Load more brands