manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Monitoring and Analyzing Switch Operation 

Status and Counters Data 

Finding the Port Connection for a Specific Device on a VLAN. 

This 

feature uses a device’s MAC address that you enter to identify the port used 
by that device. 

1.   Proceeding from figure B-8, press 

[S]

 (for 

Search

), to display the following 

prompt: 

Enter MAC address: _ 

2.   Type the MAC address you want to locate and press 

[Enter]

. The address 

and port number are highlighted if found. If the switch does not find the 
MAC address on the currently selected VLAN, it leaves the MAC address 
listing empty. 

Located MAC 
Address and 
Corresponding 
Port Number 

Figure B-9.  Example of Menu Indicating Located MAC Address 

3.   Press 

[P]

 (for 

Prev page

) to return to the full address table listing. 

Port-Level MAC Address Viewing and Searching. 

This feature displays 

and searches for MAC addresses on the specified port instead of for all ports 
on the switch. 

1.   From the Main Menu, select: 

1. Status and Counters 

7. Port Address Table 

B-14 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Aube Technologies TI034-3W Installation And User Manual preview
TI034-3W
Brand: Aube Technologies Pages: 118
HMS Networks Anybus SP2555 Startup Manual preview
Anybus SP2555
Brand: HMS Networks Pages: 16
hager TS 204 User Instruction preview
TS 204
Brand: hager Pages: 2
FS IES3110-8TF Quick Start Manual preview
IES3110-8TF
Brand: FS Pages: 33
Technische Alternative AI5S-DL Operator'S And Programming Manual preview
AI5S-DL
Brand: Technische Alternative Pages: 4
TRENDnet TE100-S5 Lühike Paigaldusjuhend preview
TE100-S5
Brand: TRENDnet Pages: 11
Orei UHD-401MV User Manual preview
UHD-401MV
Brand: Orei Pages: 27
Pakedge SE-18 Quick Start Manual preview
SE-18
Brand: Pakedge Pages: 12
ADS Technologies USBH-604 Connection Manual preview
USBH-604
Brand: ADS Technologies Pages: 2
Radware Alteon 5208 Memory Upgrade Procedure preview
Alteon 5208
Brand: Radware Pages: 4
Comet Labs 48-Port 10 User Manual preview
48-Port 10
Brand: Comet Labs Pages: 46
Control 4 LSZ-101-W Installation And User Manual preview
LSZ-101-W
Brand: Control 4 Pages: 2
Eneo 230033 Quick Installation Manual preview
230033
Brand: Eneo Pages: 19
Kathrein EXE 1512 Manual preview
EXE 1512
Brand: Kathrein Pages: 41
Gefen HDMI-341 User Manual preview
HDMI-341
Brand: Gefen Pages: 12
Greengate VNLW-P-1001-MV-N-W Installation Instructions Manual preview
VNLW-P-1001-MV-N-W
Brand: Greengate Pages: 2
IMI SENSORS 686B0X-0003 Installation And Operating Manual preview
686B0X-0003
Brand: IMI SENSORS Pages: 41
Tripp Lite B005-HUA4 Owner'S Manual preview
B005-HUA4
Brand: Tripp Lite Pages: 32

Brands by name

Popular brands

Load more brands