HP ProCurve 2610-24 Management And Configuration Manual Download Page 374

Page: 374 / 464

Monitoring and Analyzing Switch Operation

Status and Counters Data

CLI Access To Port and Trunk Group Statistics

To Display the Port Counter Summary Report.

This command provides

an overview of port activity for all ports on the switch.

Syntax

show interfaces

To Display a Detailed Traffic Summary for Specific Ports.

This com

mand provides traffic details for the port(s) you specify.

Syntax

show interfaces [ethernet]

< port-list >

To Reset the Port Counters for a Specific Port.

This command resets

the counters for the specified ports to zero for the current session. (See the
“Note on Reset” on page B-10.)

Syntax

clear statistics < [ethernet]

port-list

Web Browser Access To View Port and Trunk Group Statistics

1. Click on the

Status

tab.

2. Click on

Port Counters

3. To reset the counters for a specific port, click anywhere in the row for

that port, then click on

Refresh

Viewing the Switch’s MAC Address Tables

Feature

Default

Menu

CLI

Web

viewing MAC addresses on all
ports on a specific VLAN

n/a

page B-13

page B-15

—

viewing MAC addresses on a

n/a

page B-14

page B-15

—

specific port

searching for a MAC address

n/a

page B-14

page B-16

—

These features help you to view:

■

The MAC addresses that the switch has learned from network devices
attached to the switch

■

The port on which each MAC address was learned

B-12

Summary of Contents for ProCurve 2610-24
















































































































































































































































































































































































































































































Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands

HP ProCurve 2610-24, Management And Configuration Manual

Search results

Summary of Contents for ProCurve 2610-24

Reviews:

Related manuals for ProCurve 2610-24

Brands by name

Popular brands