manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Using the Menu Interface 

Starting and Ending a Menu Session 

Asterisk indicates a 
configuration change 
that requires a reboot 
to activate. 

Figure 3-2.  An Asterisk Indicates a Configuration Change Requiring a Reboot 

1.   In the current session, if you have not made configuration changes that 

require a switch reboot to activate, return to the Main Menu and press 

[0] 

(zero) to log out. Then just exit from the terminal program, turn off the 
terminal, or quit the Telnet session. 

2.   If you 

have 

made configuration changes that require a switch reboot— 

that is, if an asterisk (

*

) appears next to a configured item or next to 

Switch 

Configuration

 in the Main Menu: 

a.   Return to the Main Menu. 

b.   Press 

[6]

 to select 

Reboot Switch 

and follow the instructions on the 

reboot screen. 

Rebooting the switch terminates the menu session, and, if you are using 
Telnet, disconnects the Telnet session.

 (See “Rebooting To Activate Configuration Changes” on page 3-13).) 

3.   Exit from the terminal program, turn off the terminal, or close the Telnet 

application program. 

3-6 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

TAMS 1800 Series Installation & Operation Manual preview
1800 Series
Brand: TAMS Pages: 28
H3C Mini Series Manual preview
Mini Series
Brand: H3C Pages: 17
Raritan dominion kx III Quick Setup Manual preview
dominion kx III
Brand: Raritan Pages: 6
Raritan Dominion KX II Quick Installation And Setup Manual preview
Dominion KX II
Brand: Raritan Pages: 5
Raritan DOMINION KSX II Quick Setup Manual preview
DOMINION KSX II
Brand: Raritan Pages: 7
Raritan Dominion KX Quick Installation And Setup Manual preview
Dominion KX
Brand: Raritan Pages: 2
Raritan IP-Reach IPR-M1 Specifications preview
IP-Reach IPR-M1
Brand: Raritan Pages: 4
FLIR ACCDPS281B Quick Start Manual preview
ACCDPS281B
Brand: FLIR Pages: 2
MuxLab HM44 User Manual preview
HM44
Brand: MuxLab Pages: 32
Pilz PSEN 1.2p-25 Operating Instructions Manual preview
PSEN 1.2p-25
Brand: Pilz Pages: 8
Kramer VS-211X Quick Start Manual preview
VS-211X
Brand: Kramer Pages: 2
Edimax ER-5397P User Manual preview
ER-5397P
Brand: Edimax Pages: 8
TRENDnet TK-423K - USB/PS/2 KVM Switch Quick Installation Manual preview
TK-423K - USB/PS/2 KVM Switch
Brand: TRENDnet Pages: 14
Zektor HDS4x2 User Manual preview
HDS4x2
Brand: Zektor Pages: 30
TRENDnet TE100-S24g Specifications preview
TE100-S24g
Brand: TRENDnet Pages: 2
Elk Products ELK-M1DBHR Installation Manual preview
ELK-M1DBHR
Brand: Elk Products Pages: 2
Kramer VP-772T Quick Start Manual preview
VP-772T
Brand: Kramer Pages: 4
Cables to Go UH846 User Manual preview
UH846
Brand: Cables to Go Pages: 3

Brands by name

Popular brands

Load more brands