manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Monitoring and Analyzing Switch Operation 

Port and Static Trunk Monitoring Features 

Menu: Configuring Port and Static Trunk Monitoring 

This procedure describes configuring the switch for monitoring when moni­
toring is disabled. (If monitoring has already been enabled, the screens will 
appear differently than shown in this procedure.) 

1.   From the Console Main Menu, Select: 

2. Switch Configuration... 

3. Network Monitoring Port 

Enable monitoring 
by setting this 
parameter to “Yes”. 

Figure B-19. The Default Network Monitoring Configuration Screen 

2.   In the Actions menu, press 

[E]

 (for 

Edit

). 

3.   If monitoring is currently disabled (the default) then enable it by pressing 

the Space bar (or 

[Y]

) to select

 Yes. 

4.   Press the down arrow key to display a screen similar to the following and 

move the cursor to the 

Monitoring Port 

parameter. 

B-24 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

Gefen HD-441 User Manual preview
HD-441
Brand: Gefen Pages: 11
D-Link xStack DES-3500 Series Cli Manual preview
xStack DES-3500 Series
Brand: D-Link Pages: 260
D-Link DXS-3600 Series Reference Manual preview
DXS-3600 Series
Brand: D-Link Pages: 48
D-Link DXS-3400 SERIES Quick Start Manual preview
DXS-3400 SERIES
Brand: D-Link Pages: 3
D-Link Web Smart Switch DGS-1210-16 Product Manual preview
Web Smart Switch DGS-1210-16
Brand: D-Link Pages: 71
D-Link DGS-1016A Datasheet preview
DGS-1016A
Brand: D-Link Pages: 3
D-Link DGS-1100-26MP Getting Started Manual preview
DGS-1100-26MP
Brand: D-Link Pages: 56
D-Link xStack DES-3800 Series Cli Manual preview
xStack DES-3800 Series
Brand: D-Link Pages: 326
D-Link xStack DES-3526 Cli Manual preview
xStack DES-3526
Brand: D-Link Pages: 222
D-Link DGS-1008G Quick Install Manual preview
DGS-1008G
Brand: D-Link Pages: 2
D-Link DXS-1210 Series Manual preview
DXS-1210 Series
Brand: D-Link Pages: 20
Eaton COOPER POWER SERIES Installation And Operation Instructions Manual preview
COOPER POWER SERIES
Brand: Eaton Pages: 16
IDK MSD-804FD Series Command Manual preview
MSD-804FD Series
Brand: IDK Pages: 133
IDK MSD-72 Series User Manual preview
MSD-72 Series
Brand: IDK Pages: 150
IDK MSD-501 Command Reference Manual preview
MSD-501
Brand: IDK Pages: 101
IDK MSD-402 Command Reference Manual preview
MSD-402
Brand: IDK Pages: 85
IDK IMP-400UHD Command Reference Manual preview
IMP-400UHD
Brand: IDK Pages: 40
IDK FDX-32 User Manual preview
FDX-32
Brand: IDK Pages: 97

Brands by name

Popular brands

Load more brands