manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

Configuring for Network Management Applications 

LLDP (Link-Layer Discovery Protocol) 

Displaying Switch Information Available for Outbound 
Advertisements 

These commands display the current switch information that will be used to 
populate outbound LLDP advertisements. 

Syntax 

show lldp info local-device [ 

port-list

 ] 

Without the 

[ 

port-list 

] 

option, this command displays the global 

switch information and the per-port information currently 
available for populating outbound LLDP advertisements. 

With the 

[ 

port-list 

] 

option, this command displays only the 

following port-specific information that is currently available 
for outbound LLDP advertisements on the specified ports: 

•  PortType 
•  PortId 
•  PortDesc 

Note:

 This command displays the information available on 

the switch. Use the 

lldp config < 

port-list

 >

 command to change 

the selection of information that is included in actual 
outbound advertisements. In the default LLDP configuration, 
all information displayed by this command is transmitted in 
outbound advertisements. 

For example, in the default configuration, the switch information currently 
available for outbound LLDP advertisements appears similar to the display in 
figure 13-18 on page page 13-47. 

13-46 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

GAIM Compact Troubleshooting preview
Compact
Brand: GAIM Pages: 2
GE SecoGear User Manual preview
SecoGear
Brand: GE Pages: 36
GE Power Break Installation Instructions Manual preview
Power Break
Brand: GE Pages: 8
Eaton TRIPP LITE Series Quick Start Manual preview
TRIPP LITE Series
Brand: Eaton Pages: 8
Cudy GS1016 Quick Installation Manual preview
GS1016
Brand: Cudy Pages: 2
Waters Network Systems GS1016 Operating Manual preview
GS1016
Brand: Waters Network Systems Pages: 12
Greengate VNLW-P-1001-MV-N-V Installation Instructions preview
VNLW-P-1001-MV-N-V
Brand: Greengate Pages: 2
Key Digital HD Flash 4 KD-SW4x1 Operating Instructions Manual preview
HD Flash 4 KD-SW4x1
Brand: Key Digital Pages: 12
SIIG AV-GM08G3-S1 Manual preview
AV-GM08G3-S1
Brand: SIIG Pages: 17
XtendLan MATRIX1608A User Manual preview
MATRIX1608A
Brand: XtendLan Pages: 24
Radio Systems HUB16-DC Technical Manual preview
HUB16-DC
Brand: Radio Systems Pages: 19
3onedata IES2008 Quick Installation Manual preview
IES2008
Brand: 3onedata Pages: 2
Cabletron Systems SmartSwitch SBU128 User Manual preview
SmartSwitch SBU128
Brand: Cabletron Systems Pages: 76
DeLOCK 11481 User Manual preview
11481
Brand: DeLOCK Pages: 26
ATEN VM7104 Quick Start Manual preview
VM7104
Brand: ATEN Pages: 2
Dahua D-PFS3110-8ET1GT1GF-96 Quick Start Manual preview
D-PFS3110-8ET1GT1GF-96
Brand: Dahua Pages: 17
ATEN Master View CS-172 User Manual preview
Master View CS-172
Brand: ATEN Pages: 1
Wyrestorm SW-740-TX Quick Start Manual preview
SW-740-TX
Brand: Wyrestorm Pages: 4

Brands by name

Popular brands

Load more brands