manualshive.com logo in svg

HP ProCurve 2610-24, Management And Configuration Manual

The HP ProCurve 2610-24 is a reliable networking switch designed for efficient management and configuration. For easy and hassle-free setup, make sure to download the comprehensive Management And Configuration Manual from manualshive.com. This manual is available for free download, providing valuable guidance for optimizing the performance of your device.

Share
Download
background image

File Transfers 

Downloading Switch Software 

CLI: TFTP Download from a Server to Primary 
or Secondary Flash 

This command automatically downloads a switch software image to primary 
or secondary flash. 

Syntax

: 

copy tftp flash < 

ip-address 

> < 

remote-os-file 

> [< primary | secondary >] 

Note that if you do not specify the flash destination, the Xmodem download 
defaults to primary flash. 

For example, to download a switch software file named G0502.swi from a 
TFTP server with the IP address of 10.28.227.103 to primary flash: 

1.   Execute 

copy

 as shown below: 

Dynamic counter continually displays the 
number of bytes transferred. 

This message means that the image you 
want to upload will replace the image 
currently in primary flash. 

Figure A-3.  Example of the Command to  Download Switch Software 

2.   When the switch finishes downloading the switch software file from the 

server, it displays this progress message: 

Validating and Writing System Software to FLASH . . . 

3.   When the switch is ready to activate the downloaded software you will 

see this message: 

System software written to FLASH. 

You will need to reboot to activate. 

At this point, use the boot command to reboot the switch and activate the 
software you just downloaded: 

ProCurve # boot 

(For more on these commands, refer to “Rebooting the Switch” on page 
6-18.) 

4.   To confirm that the switch software downloaded correctly, execute 

show 

system

 and check the Firmware revision line. 

If you need information on primary/secondary flash memory and the boot 
commands, refer to “Using Primary and Secondary Flash Image Options” on 
page 6-13. 

A-6 

Summary of Contents for ProCurve 2610-24

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ProCurve 2610-24

D-Link DUB-1340 Datasheet preview
DUB-1340
Brand: D-Link Pages: 2
D-Link DKVM-4U Specifications preview
DKVM-4U
Brand: D-Link Pages: 2
D-Link DKVM-16 - KVM Switch Manual preview
DKVM-16 - KVM Switch
Brand: D-Link Pages: 24
D-Link Dis-200G Series Web Ui Reference Manual preview
Dis-200G Series
Brand: D-Link Pages: 161
D-Link Dis-200G Series Quick Installation Manual preview
Dis-200G Series
Brand: D-Link Pages: 16
D-Link Dis-200G Series Hw Installation Manual preview
Dis-200G Series
Brand: D-Link Pages: 47
D-Link DGS-3130-30PS Quick Installation Manual preview
DGS-3130-30PS
Brand: D-Link Pages: 25
D-Link DGS-3100 SERIES Hardware Installation Manual preview
DGS-3100 SERIES
Brand: D-Link Pages: 54
D-Link DGS-3100 SERIES Cli Manual preview
DGS-3100 SERIES
Brand: D-Link Pages: 220
D-Link DGS-3000-28SC Quick Installation Manual preview
DGS-3000-28SC
Brand: D-Link Pages: 24
D-Link DGS-1248T - Switch Manual preview
DGS-1248T - Switch
Brand: D-Link Pages: 52
D-Link DGS-1216T - Switch Getting Started Manual preview
DGS-1216T - Switch
Brand: D-Link Pages: 42
D-Link DGS-1216T - Switch Quick Installation Guid preview
DGS-1216T - Switch
Brand: D-Link Pages: 10
D-Link DGS-1010MP Installation Manual preview
DGS-1010MP
Brand: D-Link Pages: 8
D-Link DES-3350SR Command Line Interface Reference Manual preview
DES-3350SR
Brand: D-Link Pages: 379
D-Link DES-3326SR Manual preview
DES-3326SR
Brand: D-Link Pages: 240
D-Link DES-3350SR User Manual preview
DES-3350SR
Brand: D-Link Pages: 188
D-Link DES-3326S - Switch - Stackable User Manual preview
DES-3326S - Switch - Stackable
Brand: D-Link Pages: 349

Brands by name

Popular brands

Load more brands