FINAL DRIVE
Keep d u s t a n d d irt
out o f the case ar.d
cover.
GEAR TOOTH CONTACT PATTERN
CHECK
Description of the tooth:
COAST SIDE
(contacts when engine brak'ng is applied)
HEEL (out sice of gear)
J
TOE (inside of gear)
DRIVE SIDE
(contacts when engine power is applied)
Clean the sealing material off the mating surfaces of
the gear case and cover, being careful not to dam
age them.
Apply a thin coat of Prussian Blue to the pinion gear
teeth.
Select the replacement shaft shim (page 14-10).
Install the shaft shim.
Install the case cover and tighten the bolts in a criss
cross pattern in several steps until the cover evenly
touches the gear case.
Install and tighten the tw o 10 mm bolts to the speci
fied torque in several steps alternately.
TORQUE: 47 N-m (4.8 kgf-m, 35 Ibf-ft)
Tighten the six 8 mm bolts to the specified torque in
a crisscross pattern in several times.
TORQUE: 25 N-m (2.6 kgf-m, 19 Ibf-ft)
8
Remove the oil fille r cap.
Rotate the ring gear several times in normal direc
tion of rotation.
Check the gear tooth contact pattern through the oil
fille r hole.
Contact is normal if the Prussian Blue is transferred
to the approximate center of each tooth and slightly
tow ards the face.
If the patterns are not correct, remove and replace the
pinion gear shim with a suitable one (page 14-15).
Apply Prussian Blue
SHAFT SHIM
10 mm BOLTS
mm BOLTS
GEAR CASE COVER
Normal:
PINION SHIM
HEEL
FACE
▼
DRIVE
FLANK
SIDE
TOE
HEEL
face
COAST
SIDE
FLANK
14-11
Summary of Contents for NSA700A DN-1 2009
