3 . I n s t r u c t i o n S e t
M N 0 5 0 0 3 0 0 3 E F o r m o r e i n f o r m a t i o n v i s i t : w w w. e a t o n . c o m
3 - 5 0 1
For example, set
S
1
+0 to K1 for the speed range 1Hz~1KHz, K10 for the speed range
10Hz~10KHz, K100 for the speed range 100Hz~10KHz.
7.
D
occupies 3 consecutive 16-bit registers.
D
+0 specifies the output proportional value. Valid
range: K1 (1%) ~ K10000 (10000%). If the specified value exceeds the valid range, the ELC
will take the lower/upper bound value as the set value. Output proportion can be changed
during ELC operation, however the modified value will not take effect until the next time the
program scans the instruction.
D
+2 and
D
+1 indicates the output speed as a 32-bit value.
Units: 1Hz. Valid range:
±
100kHz.
8.
The speed sampled by the ELC will be multiplied with the output proportional value
D
+0, then
the ELC will generate the actual output speed. The ELC will take the integer of the calculated
value, i.e. if the calculated result is smaller than 1Hz, the ELC will output 0Hz. For example,
input speed: 10Hz, output proportion: K5 (5%), then the calculation result will be 10 x 0.05 =
0.5Hz. The Pulse output will be 0Hz; if output proportion is changed to K15 (15%), then the
calculation result will be 10 x 0.15 = 1.5Hz. Pulse output will be 1Hz.
Program Example:
1.
If D0 is set to K2 and D10 is set to K100:
When the sampled speed is on (X0, X1) is +10Hz (D1 = K10), (Y0, Y1) pulses will be sent at
+10Hz (D12, D11 = K10); When the sampled speed is -10Hz (D1 = K-10), (Y0, Y1) pulses will
be sent at -10Hz (D12, D11 = K-10)
2.
If D0 is set to K2 and D10 is set to K1000:
When the sampled speed is on (X0, X1) is +10Hz (D1 = K10), (Y0, Y1) will output pulses with
+100Hz (D12, D11 = K100); When the sampled speed is -100Hz (D1 = K-100), (Y0, Y1) pulses
will be sent at -100Hz (D12, D11 = K-100)
3.
If D0 is set to K10 and D10 is set to K10:
When the sampled speed is on (X0, X1) is +10Hz (D1 = K10), (Y0, Y1) will output pulses with
+1Hz (D12, D11 = K1); When the sampled speed is -10Hz (D1 = K-10), (Y0, Y1) pulses will be
sent at -1Hz (D12, D11 = K-1)
M 0
CSF O
X1
D10
D0
Summary of Contents for ELC-PB
