Cisco XR 1200 series Command Reference Manual Download Page 168

Page: 168 / 432

lives

To set the number of lives that are maintained in the history table for an IP SLA operation, use the

lives

command in IP SLA operation history configuration mode. To use the default value, use the

form of this

command.

lives lives

no lives

Syntax Description

Number of lives that are maintained in the history table for an IP SLA operation.
Range is 0 to 2.

lives

Command Default

The default value is 0 lives.

Command Modes

IP SLA operation history configuration

Command History

Modification

Release

This command was introduced.

Release 3.3.0

Usage Guidelines

The

lives

command is supported only to configure the following operations:

•

IP SLA ICMP path-echo

•

IP SLA ICMP echo

•

IP SLA UDP echo

If you use the

form of the

lives

command, the history statistics are not collected.

Task ID

Operations

Task ID

read, write

monitor

Examples

The following example shows how to use the

lives

command in IP SLA UDP echo configuration mode:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

RP/0/0/CPU0:router(config-ipsla)#

operation 1

RP/0/0/CPU0:router(config-ipsla-op)#

type udp echo

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

156

OL-24735-01

IP Service Level Agreement Commands

lives

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands