Cisco XR 1200 series Command Reference Manual Download Page 187

Page: 187 / 432

output interface

To specify the echo request output interface to be used for LSP ping or LSP trace operations, use the

output

interface

command in IP SLA MPLS LSP ping or IP SLA MPLS LSP trace configuration mode. To return

the output interface to the default, use the

form of this command.

output interface type interface-path-id

no output interface

Syntax Description

Interface type. For more information, use the question mark (

) online help function.

type

Physical interface or virtual interface.

Use the

show interfaces

command to see a list of all interfaces currently

configured on the router.

Note

For more information about the syntax for the router, use the question mark (

) online

help function.

interface-path-id

Command Default

No default behavior or values.

Command Modes

IP SLA MPLS LSP ping configuration

IP SLA MPLS LSP trace configuration

IP SLA MPLS LSP monitor ping configuration

IP SLA MPLS LSP monitor trace configuration

Command History

Modification

Release

This command was introduced.

Release 3.5.0

Usage Guidelines

Use the

output interface

command to help monitor path-to-target over the path if there are some ECMP

routes in a topology.

You cannot use the

output interface

command if pseudowire is specified as the target to be used in an MPLS

LSP ping operation.

Task ID

Operations

Task ID

read, write

monitor

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

175

IP Service Level Agreement Commands

output interface

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands