Cisco XR 1200 series Command Reference Manual Download Page 198 | Manualshive

Page: 198 / 432

background image

path discover path

To configure MPLS LSP path parameters, use the

path discover path

command in MPLS LSP monitor

(MPLSLM) LPD configuration submode. To use the default value, use the

no

form of this command.

path discover path

{

retry range

|

secondary frequency

{

both| connection-loss| timeout

}

value

}

no path-discover path

Syntax Description

Configures the number of attempts to be performed before declaring a path
as down. Default is 1 (LSP group will not retry to perform the echo request
if the previous attempt fails). Range is 1 to 16.

retry range

Configures a secondary frequency to use after a failure condition (that is, a
connection-loss or timeout) occurs.

secondary frequency

Enable secondary frequency for a timeout and connection loss.

both

Enable secondary frequency for only a connection loss.

connection-loss

Enable secondary frequency for only a timeout.

timeout

Frequency value range is 1 to 604800.

value

Command Default

None

Command Modes

MPLSLM LPD configuration

Command History

Modification

Release

This command was introduced.

Release 3.6.0

Usage Guidelines

In the event of a path failure, the secondary frequency value is used instead of the normal frequency value.
The normal frequency value is determined by a frequency value or schedule period value, and the LSP
operations are scheduled to start periodically at this interval. By default, the secondary frequency value is
disabled. When failure condition disappears, probing resumes at the regular frequency.

The secondary command works in tandem with the retry keyword. Both must be configured.

Note

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

186

OL-24735-01

IP Service Level Agreement Commands

path discover path

«
...
196
197
198
199
200
...
»

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XR 1200 series

Brand: DBM Pages: 50

Power Xpert Meter 2000

Brand: Eaton Pages: 16

POW-R-COMMAND 1000

Brand: Eaton Pages: 84

Brand: WAGO Pages: 2

Nighthawk M6 Pro

Brand: AT&T Pages: 2

Brand: Lancom Pages: 25

Brand: HARTING Pages: 13

Brand: Teletronics International Pages: 57

Brand: StarTech.com Pages: 9

GSM7224v2 - Layer 2 Managed Gigabit Switch

Brand: NETGEAR Pages: 3

Husky HMG-1648EP

Brand: Ethernet Direct Pages: 16

Brand: InHand Pages: 69

RuggedSwitch RS500

Brand: RuggedCom Pages: 16

Wireless Kit 108MBPS

Brand: Topcom Pages: 100

3C13755-US - Router 5642

Brand: 3Com Pages: 104

Brand: NAUTICAST Pages: 20

Brand: Icy Box Pages: 17

Schoeps electret

Brand: VAMISOUND Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands