Cisco XR 1200 series Command Reference Manual Download Page 57 | Manualshive

Page: 57 / 432

background image

rootcause

To specify the root-cause alarm message, use the

rootcause

command in stateful or nonstateful correlation

rule configuration modes.

rootcause msg-category group-name msg-code

no rootcause

Syntax Description

Message category of the root message.

msg-category

Group name of the root message.

group-name

Message code of the root message.

msg-code

Command Default

Root-cause alarm is not specified.

Command Modes

Stateful correlation rule configuration

Nonstateful correlation rule configuration

Command History

Modification

Release

This command was introduced.

Release 3.6.0

Usage Guidelines

This command is used to configure the root-cause message for a particular correlation rule. Messages are
identified by their message category, group, and code. The category, group, and code each can contain up to
32 characters. The root-cause message for a stateful correlation rule should be a bi-state alarm.

Use the

show logging events info, on page 62

command to display the root-cause and non-root-cause alarms

for a correlation rule.

Task ID

Operations

Task ID

read, write

logging

Examples

This example shows how to configure a root-cause alarm for a stateful correlation rule:

RP/0/0/CPU0:router(config)#

logging correlator rule state_rule type stateful

RP/0/0/CPU0:router(config-corr-rule-st)#

rootcause L2 SONET_LOCAL ALARM

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

45

Alarm Management and Logging Correlation Commands

rootcause

«
...
55
56
57
58
59
...
»

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XR 1200 series

DG834GT - 108 Mbps Super G Wireless ADSL Router

Brand: NETGEAR Pages: 2

LinkSmart KW6515

Brand: Kasda Pages: 31

8677 - BladeCenter Rack-mountable - Power Supply

Brand: IBM Pages: 126

Brand: Conel Pages: 32

Brand: ivideon Pages: 11

Brand: Airvana Pages: 90

i.LON SmartServer

Brand: Echelon Pages: 34

Brand: Dinstar Pages: 103

7798 I/SITE LAN

Brand: CSI Pages: 56

Brand: R3 Pages: 48

SmartNode 4634 Series

Brand: Patton electronics Pages: 12

Brand: TP-Link Pages: 2

Brand: Avaya Pages: 2

Brand: bintec elmeg Pages: 32

Brand: HALNy Pages: 12

Brand: Billion Pages: 12

Brand: MikroTik Pages: 4

BouterBoard hAP

Brand: MikroTik Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands