Cisco XR 1200 series Command Reference Manual Download Page 390

Page: 390 / 432

Command Default

Threshold collection is disabled.

Command Modes

Global configuration

Command History

Modification

Release

This command was introduced.

Release 2.0

The

enable

keyword was replaced by the

apply

keyword. In previous releases,

this command was referred to as

performance-mgmt enable thresholds

The

disable

keyword was deprecated.

The

ospf v2protocol

and

ospf v3protocol

keywords were introduced to

support the enabling of threshold monitoring templates for the OSPF entity.

The

location

keyword was added. The

global

keyword was deprecated and

replaced by the

location all

keywords.

Release 3.2

Removed support for MPLS interfaces.

Release 3.3.0

The

interface basic-counters

keyword was added to support the enabling of

threshold monitoring template for the basic counter.

Release 4.0.1

Usage Guidelines

Use the

performance-mgmt apply thresholds

command to apply a threshold template and enable threshold

collection. Several templates can be configured, but only one template for each entity can be enabled at a
time.

Use the

form of the command to disable threshold collection. Because only one performance management

threshold monitoring template can be enabled for any given entity at any given time, you are not required to
specify the template name with the

default

keyword or

template

keyword and

template-name

argument when

disabling a performance management statistics collection.

For information about creating threshold templates, see the

performance-mgmt thresholds, on page 389

command.

Task ID

Operations

Task ID

read, write, execute

monitor

Examples

This example shows how to start threshold collection for BGP using a template named stats1:

RP/0/0/CPU0:router(config)#

performance-mgmt apply thresholds bgp stats1

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

378

OL-24735-01

Performance Management Commands

performance-mgmt apply thresholds

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands