Cisco XR 1200 series Command Reference Manual Download Page 394 | Manualshive

Page: 394 / 432

background image

performance-mgmt resources memory

To configure memory consumption limits for performance management (PM), use the

performance-mgmt

resources memory

command in global configuration mode. To restore the default memory consumption

limits, use the

no

form of this command.

performance-mgmt resources memory max-limit kilobytes min-reserved kilobytes

no performance-mgmt resources memory

Syntax Description

Specifies the maximum amount of memory (specified with the

kilobytes

argument)

that the PM statistics collector can use for serving data collection requests. Range
is 0 to 4294967295 kilobytes.The default is 50000 kilobytes.

max-limit kilobytes

Specifies a minimum amount of memory (specified with the

kilobytes

argument)

that must remain available in the system after allowing a new PM data collection
request. Range is 0 to 4294967295 kilobytes. The default is 10000 kilobytes.

min-reserved kilobytes

Command Default

max-limit

—

50000

kilobytes

min-reserved

—

10000 kilobytes

Command Modes

Global configuration

Command History

Modification

Release

This command was introduced.

Release 3.2

Usage Guidelines

Use the

performance-mgmt resource memory

command to ensure that the total memory consumed by data

buffers in PM does not exceed a maximum limit and that any new PM data request does not cause available
memory in the system to fall below a certain threshold.

Task ID

Operations

Task ID

read, write

monitor

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

382

OL-24735-01

Performance Management Commands

performance-mgmt resources memory

«
...
392
393
394
395
396
...
»

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XR 1200 series

EtherLink 3C509B

Brand: 3Com Pages: 8

VigorIPPBX 2820 Series

Brand: Draytek Pages: 29

Brand: Dahua Pages: 6

Brand: IBM Pages: 32

JetWeb JX2-PR0FI1

Brand: Jetter Pages: 67

Brand: Variscite Pages: 18

Brand: UfiSpace Pages: 32

ELITENAS EN104L+(B)

Brand: Sans Digital Pages: 9

Brand: FOR-A Pages: 2

Brand: Ubiquiti Pages: 23

Brand: Ubiquiti Pages: 20

Brand: Milesight Pages: 15

TE100S8P - Fast Ethernet Switch

Brand: TRENDnet Pages: 11

Brand: Vaisala Pages: 32

Brand: Planet Pages: 16

Brand: Vivotek Pages: 46

Sporlan Division SCS-PB Series

Brand: Parker Pages: 10

Internet Security Appliances

Brand: SonicWALL Pages: 293

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands