Cisco XR 1200 series Command Reference Manual Download Page 275 | Manualshive

Page: 275 / 432

background image

target pseudowire

To specify the pseudowire as the target to be used in an MPLS LSP ping operation, use the

target pseudowire

command in IP SLA MPLS LSP ping configuration mode. To unset the target, use the

no

form of this command.

target pseudowire destination-address circuit-id

no target pseudowire

Syntax Description

IPv4 address of the target device to be tested.

destination-address

Virtual circuit identifier. Range is 1 to 4294967295.

circuit-id

Command Default

No default behavior or values

Command Modes

IP SLA MPLS LSP ping configuration

Command History

Modification

Release

This command was introduced.

Release 3.5.0

Usage Guidelines

Use the

target pseudowire

command to specify a target router and to indicate the destination as a Layer 2

VPN pseudowire in an MPLS LSP ping operation. The

target pseudowire

command identifies the target

address and the virtual circuit (VC) identifier.

Using the

target pseudowire

command, you can configure only one pseudowire address as the target in

an MPLS LSP ping operation. If you use the command a second time and configure a different pseudowire
target address, the first pseudowire address is overwritten.

Note

A pseudowire target of the LSP ping operation allows active monitoring of statistics on Pseudowire
Edge-to-Edge (PWE3) services across an MPLS network. PWE3 connectivity verification uses the Virtual
Circuit Connectivity Verification (VCCV).

For more information on VCCV, refer to the VCCV draft,

“

Pseudowire Virtual Circuit Connectivity Verification

(VCCV)

”

on the IETF web page.

Task ID

Operations

Task ID

read, write

monitor

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

263

IP Service Level Agreement Commands

target pseudowire

«
...
273
274
275
276
277
...
»

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XR 1200 series

TokenLink 3C359B

Brand: 3Com Pages: 4

TokenLink 3C359B

Brand: 3Com Pages: 8

TokenLink 3C339

Brand: 3Com Pages: 2

EtherLink 3C985B-SX

Brand: 3Com Pages: 44

Brand: 3Com Pages: 88

Brand: 3Com Pages: 2

Brand: 3Com Pages: 111

TokenLink 3C359

Brand: 3Com Pages: 4

Brand: 3Com Pages: 74

Brand: 3Com Pages: 6

Brand: H3C Pages: 45

Brand: H3C Pages: 80

Brand: H3C Pages: 46

Brand: H3C Pages: 45

Brand: H3C Pages: 4

Brand: H3C Pages: 184

Brand: IBM Pages: 32

DR-4100P Series

Brand: Idis Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands