Cisco XR 1200 series Command Reference Manual Download Page 287

Page: 287 / 432

threshold type xofy

To take action upon X violations in Y probe operations, use the

threshold type xofy

command in IP SLA

reaction condition configuration mode. To clear the threshold type (reaction will never happen), use the

form of this command.

threshold type xofy x-value y-value

no threshold type

Syntax Description

When the reaction conditions, such as threshold violations, are met for the monitored
element after some

number of violations within some other

number of probe

operations (for example,

), the action is performed as defined by the

action

command. Default is 5 for both

x-value

and

y-value;

for example,

xofy 5 5

. Range is 1

to 16.

x-value y-value

Command Default

If there is no default value, no threshold type is configured.

Command Modes

IP SLA reaction condition configuration

Command History

Modification

Release

This command was introduced.

Release 3.3.0

Usage Guidelines

Task ID

Operations

Task ID

read, write

monitor

Examples

The following example shows how to use the

threshold type xofy

command:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

RP/0/0/CPU0:router(config-ipsla)#

reaction operation 432

RP/0/0/CPU0:router(config-ipsla-react)#

react verify-error

RP/0/0/CPU0:router(config-ipsla-react-cond)#

threshold type xofy 1 5

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

275

IP Service Level Agreement Commands

threshold type xofy

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands

Cisco XR 1200 series, Command Reference Manual

Search results

Summary of Contents for XR 1200 series

Reviews:

Related manuals for XR 1200 series

Brands by name

Popular brands