Cisco XR 1200 series Command Reference Manual Download Page 373 | Manualshive

Page: 373 / 432

background image

Performance Management Commands

This module describes the performance management and monitoring commands available on the router.
These commands are used to monitor, collect, and report statistics, and to adjust statistics gathering for
Border Gateway Protocol (BGP), Open Shortest Path First (OSPF) protocol, generic interfaces, and individual
nodes.

For detailed information about performance management concepts, configuration tasks, and examples, see
the

Implementing Performance Management

module in the

Cisco IOS XR System Monitoring Configuration

Guide for the Cisco XR 12000 Series Router

.

•

monitor controller fabric, page 362

•

monitor controller sonet, page 364

•

monitor interface, page 366

•

performance-mgmt apply monitor, page 371

•

performance-mgmt apply statistics, page 374

•

performance-mgmt apply thresholds, page 377

•

performance-mgmt regular-expression, page 380

•

performance-mgmt resources dump local, page 381

•

performance-mgmt resources memory, page 382

•

performance-mgmt resources tftp-server, page 384

•

performance-mgmt statistics, page 386

•

performance-mgmt thresholds, page 389

•

show performance-mgmt bgp, page 400

•

show performance-mgmt interface , page 402

•

show performance-mgmt mpls, page 405

•

show performance-mgmt node, page 407

•

show performance-mgmt ospf, page 409

•

show running performance-mgmt, page 411

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

OL-24735-01

361

«
...
371
372
373
374
375
...
»

Summary of Contents for XR 1200 series

















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for XR 1200 series

Brand: Danfoss Pages: 61

Brand: WAGO Pages: 2

Brand: NetBurner Pages: 15

Brand: Qixiang Technology Pages: 16

Brand: Lancom Pages: 70

Brand: Patton electronics Pages: 12

Brand: E-Lins Pages: 113

DesignCore RVP-TDA3 Series

Brand: D3 Pages: 34

Brand: Buffalo Pages: 2

PacketMate 1000

Brand: General DataComm Pages: 20

Brand: Alcatel-Lucent Pages: 12

Brand: Vaisala Pages: 32

Brand: H3C Pages: 4

TS-U100 - NAS Server - USB

Brand: TRENDnet Pages: 47

Brand: Icy Box Pages: 17

Brand: D-Link Pages: 74

DuraMAR 5915-2X

Brand: Parvus Pages: 40

Brand: Teltone Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands